Acti E616 Bruksanvisning
Acti
övervakningskamera
E616
Läs nedan 📖 manual på svenska för Acti E616 (37 sidor) i kategorin övervakningskamera. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 4.5 användare
Sida 1/37
Indoor Dome Series
Hardware Manual
E610, E616, E617, E618, E621
201 175/04/
www.acti.com
Hardware Manual
2
Table of Contents
Precautions ............................................................. 4
Safety Instructions .................................................................................... 6
Introduction ............................................................. 7
The List of Models ..................................................................................... 7
Package Contents ...................................................................................... 8
Physical Description ................................................................................. 9
Mounting Options ..................................................................................... 11
Other Mounting Accessories ................................................................. 13
Before Installation ................................................. 14
Connecting the DI/DO Devices (Optional) ............................................. 14
Connecting Audio In / Out Devices (Optional) ...................................... 18
Installing the Camera on a Surface ..................... 19
Step 1: Drill the Holes .............................................................................. 19
Step 2: Open the Dome Cover ................................................................ 20
Step 3: Install the Camera to the Surface .............................................. 21
Step 4: Connect the Cable ...................................................................... 22
Step 5: Access the Camera Live View .................................................... 22
Step 6: Adjust the Viewing Angle and Focus ........................................ 23
Step 7: Close the Dome Cover ................................................................ 23
www.acti.com
Hardware Manual
3
Other Adjustments and Accessories .................. 25
How to Install a Memory Card ................................................................. 25
How to Insert the Memory Card ............................................................ 25
How to Remove the Memory Card ........................................................ 25
How to Adjust the Viewing Angle and Flocus ....................................... 26
E610 ..................................................................................................... 26
E616, E617, E618, E621 ....................................................................... 28
How to Replace the Dome Cover ............................................................ 29
Accessing the Camera ......................................... 31
Congure the IP Addresses .................................................................... 31
Access the Camera .................................................................................. 35
www.acti.com
Hardware Manual
4
Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualied service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
oce if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
www.acti.com
Hardware Manual
5
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for comp authority to operate the equipment. liance could void the user’s
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to European Standard EN 55022
and EN 55024. In a domestic environment, this product may cause radio interference in which
cause the user may be required to take adequate measures.
www.acti.com
Hardware Manual
6
Safety Instructions
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Do use accessories not recommended by the manufacturer not
Install this device in a dry place protected from weather.
Servicing
Do not attempt to service this video product yourself Refer all servicing to qualied service .
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the inner parts of video product ha been directly exposed to rain or water. ve
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualied technician to restore the video product to its normal operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine the video product is in proper operating condition. if
www.acti.com
Hardware Manual
7
Introduction
The List of Models
This hardware manual contains the following models:
E 0 61
10MP Indoor Dome with D/N, Adaptive IR, Basic WDR, Vari-focal lens
E616
5MP Indoor Zoom Dome with D/N, Adaptive IR, Basic WDR,
4.3x Zoom lens
E617
10MP Indoor Zoom Dome with D/N, Adaptive IR, Basic WDR,
4.3x Zoom lens
E618
3MP Indoor Zoom Dome with D/N, Adaptive IR, Superior WDR,
4.3x Zoom lens
E621
1.3MP Indoor Zoom Dome with D/N, Adaptive IR, Superior WDR, 4.3x
Zoom lens
www.acti.com
Hardware Manual
8
Package Contents
Camera
Mounting Screw Kit
Hexagon Screwdriver
Drill Template
Terminal Block
(for DI/DO)
Terminal Block
(for Audio In/Out)
Quick Installation Guide
Warranty Card
NOTE: The above pictures are for reference only; actual items may slightly differ.
Drill Template
www.acti.com
Hardware Manual
9
Physical Description
NOTE: The camera images on this documentation are for reference only. Actual camera may
slightly dier.
1) Ethernet Port
Connects to a network using an Ethernet cable.
2) Memory Card Slot
Insert a memory card into this slot for local recording purposes. See How to Install a
Memory Card on page for more informatio 25 n.
NOTE: Supports microSDHC and microSDXC cards.
3) Digital Input / Output (DI/DO)
This connector connects to digital input or output devices, such as an alarm trigger, panic
button, etc. Digital Input (DI) and Digital Output (DO) devices are used in applications like
motion detection, event triggering, alarm notications, etc. See Connecting the DI/DO
Devices (Optional) on page for information on how to connect DI/DO devices to your 14
camera.
www.acti.com
Hardware Manual
13
Other Mounting Accessories
Accessories
PMAX-0104 (Extension Tube)
NOTE:
For more information about the mounting solutions and accessories, please check the
Mounting Accessory Selector in our website (http://www.acti.com/mountingselector).
The above mounting accessories are not included in the package. Contact your sales
agents to purchase.
www.acti.com
Hardware Manual
14
Before Installation
This section describes the procedures in preparing the external devices that you can connect to
the camera. The camera supports Digital Input and Output (DI/DO) and Audio Input and Output
devices using the bundled terminal blocks. The use of these devices, however, is optional.
Connecting the DI/DO Devices (Optional)
Depending on your surveillance needs, you may connect digital input or output devices to your
camera to trigger events or notications.
Digital Input (DI) devices can be used to notify the camera about an activity in the camera site. DI
can be triggers of events. For example, you can connect a “panic button” to the camera; as such
when the panic button is pressed, the alarm signal will be sent through the camera. Other
common DI device applications are emergency button, smoke detector, passive infrared sensor,
etc.
Digital Output (DO) devices are external devices that are activated by the camera upon an event
inside the camera. For example, you can connect an “alarm horn” to the camera; as such when
an event occurs inside the camera (e.g. detected intruder), the alarm horn will sound. Other
common DO device applications are motion-triggered lights, electric fence, magnetic door locks,
etc.
You can connect up to two DI and two DO devices to your camera.
Press and hold the orange tab as you insert the wire through the pin slot, then release the orange
tab to secure the wire.
www.acti.com
Hardware Manual
15
To connect input devices (DI), map the pins to one of the pin combinations below:
Device
Pin
Mapping Instructions
Digital Input 1 (DI 1)
GND
Connect the wires of the rst input device to GND
and DI1.
DI1
Digital Input 2 ) (DI2
GND
Connect the wires of the second input device to GND
and DI2.
DI2
To connect output devices (DO), map the pins to one of the pin combinations below:
Device
Pin
Mapping Instructions
Digital Output 1 (DO 1)
12V
Connect the wires of the rst output device to 12V
and DO1.
DO1
Digital Output 2 ) (DO2
12V
Connect the wires of the second output device to 12V
and DO2.
DO2
The table below shows the DI/DO connection specications:
Device
DI
Connection design
TTL - compatible logic levels
Voltage
To trigger (low)
Logic level 0: 0V ~ 0.4V
Normal (high)
Logic level 1: 3.1V ~ 30V
Current
10mA ~ 100mA
DO
Connection design
Transistor (Open Collector)
Voltage & Current
< 24V DC, < 50mA
Typical Connection
Based on these specifications, if the DI device has a voltage of 0V ~ 30V or the DO device has a
voltage of < 24V (< 50mA), then the camera can supply internal power to these devices and there
is no need to connect the DI/DO device to an external power source.
www.acti.com
Hardware Manual
16
In this case, wire connection to Pins 1 to 4. Use the and pins to connect a DI device and GND DI1
use the and pins to connect a DO device. See wiring scheme below: 12V DO1
Consequently, to connect a second DI or DO device, wire the connection to Pins 5 to 8.
High Voltage DO Device Connection
Even though the camera provides 12V power, this may not be enough for some high voltage DO
devices, such as a ceiling light or a motor that opens or closes a gate. In this case, there is a
need to connect an external relay. See wiring scheme below:
Note that when choosing an appropriate relay, please refer to its specications and make sure
they match the above design. The triggering circuit voltage has to be around 12V DC and the
switch-controlled circuit voltage has to match the external power supply (e.g. 110V AC or 220V
AC).
www.acti.com
Hardware Manual
17
The illustration below is a graphic example of connecting a relay to a high voltage DO device.
Relay
(DO1 Device)
Camera
Illuminator
110V-220V AC
External Power
Source
NOTE: For more information on DI/DO connections, please refer to the Knowledge Base
article All About Digital Input and Digital Output downloadable from the link below
( http://Download.acti.com?id=516).
www.acti.com
Hardware Manual
18
Connecting Audio In / Out Devices (Optional)
Depending on your surveillance needs, you may connect audio input or output device, such as an
active microphone or speaker, to your camera. In this case, you need to connect the audio
input/output device to the supplied audio terminal block.
To connect audio input / output devices, map the pins to one of the pin combinations below:
Device
Mapping Instructions
Audio Output
GND
Connect the wires of the audio output device to GND
and AUDIO.OUT.
AUDIO.OUT
Audio Input
GND
Connect the wires of the audio input device to GND
and AUDIO.IN.
AUDIO.IN
Press and hold the orange tab as you insert the wire through the pin slot, then release the orange
tab to secure the wire.
NOTE: For more information about AUDIO in connections, please refer to the Knowledge Base
article How to Use Audio-in of ACTi Cameras, downloadable from the link below
( http://Download.acti.com?id=534).
www.acti.com
Hardware Manual
20
Step 2: Open the Dome Cover
NOTE: To avoid scratches or leaving fingerprints on the dome cover, it is recommended to retain
the plastic covering the dome cover until the camera is completely installed. However, the plastic
has been removed on some of the pictures in this documentation to show clarity of the pictures
being described.
1. With the bundled hex screwdriver, loosen the three (3) screws securing the dome cover.
2. Lift to remove the dome cover.
3. If the cables will be routed along the ceiling or wall, remove the cable tab from the dome
cover.
4. If the cables will pass through the ceiling or wall, route and pull the cables through the
hole on the surface.
www.acti.com
Hardware Manual
21
Step 3: Install the Camera to the Surface
1. If necessary, insert a memory card, with the metallic contacts facing down, into the card slot
of the camera.
2. and Align the camera screw holes the cable hole (if necessary) to the holes on the surface
and attach the three (3) supplied screws to secure the camera.
CAUTION: be careful not to touch the camera When using electric screwdrivers,
components while attaching the screws. Since electric screwdrivers vary in sizes, speed, and
force, they may bruise and damage the camera components.
DISCLAIMER: ACTi will not be responsible for camera damage caused by improper
installations or the misuse of equipment for installation.
www.acti.com
Hardware Manual
22
Step 4 Connect the Cable :
1. Connect the network cable to the Ethernet port of the camera.
If necessary, connect other cable connectors (optional), like audio input/output and DI/DO to
the corresponding connectors on the camera.
2. Connect the other end of the network cable to a switch or injector. Then, connect the switch
or injector to a network, PC and a power source. See Power-over-Ethernet (PoE) connection
example below.
Network
AC Power
Source
PoE Injector /
PoE Switch
Power Cable
Ethernet Cable
Ethernet Cable
(Data + Power)
Ethernet Cable
(Data)
Camera
Step 5 Access the Camera Live View :
See on page for more information on how to access the Live View of Accessing Camerathe 31
the camera.
Ethernet Port
Digital Input / Output
(DI/DO) Connector
Audio Input / Output
Connector
www.acti.com
Hardware Manual
25
Other Adjustments and Accessories
How to Install a Memory Card
The camera supports local video recording or saving of snapshots to a memory card.
NOTE: Supports microSDHC and microSDXC cards.
How to Insert the Memory Card
Insert a memory card into the card slot with the metallic contacts facing down the camera. Push
the card until it clicks into place.
How to Remove the Memory Card
In case there is a need to remove the card, make sure to access the camera Web Congurator to
safely “unmount” the card first (see the camera Firmware manual for more information). Once
unmounted from the rmware, push the card to eject it from the slot.
www.acti.com
Hardware Manual
26
How to Adjust the Viewing Angle and Flocus
E610
Camera Parts Overview
Adjustment Procedures
1. Loosen the tilt adjustment screws, adjust the tilt, and then tighten back the screws to x
the tilt position.
2. Loosen the rotation adjustment screw, rotate the viewing orientation, and then tighten
back the screw to fix the orientation.
1
2
3
www.acti.com
Hardware Manual
27
3. Loosen the pan adjustment screw, move the pan direction, and then tighten back the
screw to x the pan position.
The camera comes with the focus and viewing angle already pre-xed. However, if you need to
change the focus and viewing angle, do the following:
1. Loosen the zoom lever screw, then move the lever left or right to adjust the viewing
angle.
2. Loosen the focus lever screw, then move the lever left or right to adjust the focus.
3. When the desired viewing angle and focus are already achieved, tighten the lever screws
again to x their position.
www.acti.com
Hardware Manual
28
E616, E617, E618, E621
Since E616, E617, E618 and E621 models are zoom cameras with auto focus feature, only the
viewing angle needs to be adjusted.
Camera Parts Overview
Adjustment Procedures
1. Loosen the tilt adjustment screws, adjust the tilt, and then tighten back the screws to x
the tilt position.
2. Loosen the rotation adjustment screw, rotate the viewing orientation, and then tighten
back the screw to fix the orientation.
1
2
3
www.acti.com
Hardware Manual
29
3. Loosen the pan adjustment screw, move the pan direction, and then tighten back the
screw to x the pan position.
How to Replace the Dome Cover
For more discrete surveillance needs, the bundled dome cover can be replaced with a smoke,
vandal proof cover available for purchase. To replace the dome cover, do the following:
1. Loosen the three (3) screws to open the dome cover.
2. Remove the three (3) screws to detach the bracket.
3. Remove bracket and dome cover from the cover housing. the
Produktspecifikationer
| Varumärke: | Acti |
| Kategori: | övervakningskamera |
| Modell: | E616 |
| Färg på produkten: | Roestvrijstaal |
| Bredd: | 900 mm |
| Djup: | 600 mm |
| Höjd: | - mm |
| Typ produkt: | Headset |
Behöver du hjälp?
Om du behöver hjälp med Acti E616 ställ en fråga nedan och andra användare kommer att svara dig
övervakningskamera Acti Manualer
1 Januari 2025
27 Oktober 2024
27 Oktober 2024
18 September 2024
16 September 2024
12 September 2024
12 September 2024
12 September 2024
12 September 2024
9 September 2024
övervakningskamera Manualer
- övervakningskamera M-e
- övervakningskamera Notifier
- övervakningskamera Overmax
- övervakningskamera Tenda
- övervakningskamera EverFocus
- övervakningskamera Arenti
- övervakningskamera TCP
- övervakningskamera Buffalo
- övervakningskamera Turing
- övervakningskamera Raymarine
- övervakningskamera Orion
- övervakningskamera Netis
- övervakningskamera Satel
- övervakningskamera EtiamPro
- övervakningskamera Hama
Nyaste övervakningskamera Manualer
5 April 2025
5 April 2025
5 April 2025
28 Januari 2025
25 Januari 2025
25 Januari 2025
16 Januari 2025
10 Januari 2025
8 Januari 2025
8 Januari 2025