Aeon Labs Z-Stick Bruksanvisning
Aeon Labs
Nätverkskort/adapter
Z-Stick
Läs gratis den bruksanvisning för Aeon Labs Z-Stick (4 sidor) i kategorin Nätverkskort/adapter. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 8 recensioner. Har du en fråga om Aeon Labs Z-Stick eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
Aeon Labs Z-Stick
(Z-Wave USB Adapter)
Introduction:
The Aeon Labs Z-Stick is a self-powered Z-Wave USB adapter with remote network creation
capabilities (independent from external power and host microprocessor). By being able to
remotely include/remove Z-Wave devices, this greatly simplifies Z-Wave network installation.
When connected to a host processor (via USB), it enables the host processor to take part in the
Z-Wave Network.
By taking advantage of the Z-Wave mesh network, commands can be routed to their
destination via intermediary “listening” Z-Wave products. Products that are Z-Wave certified
can be used and communicate with other Z-Wave certified devices.
Operating instructions:
The Z-Stick operates in three distinct modes: Inclusion-Mode, Removal-Mode and SerialAPI-
Mode. Both Inclusion-Mode and Removal-Mode require the Z-Stick to be unplugged from the
USB connector of the host, while SerialAPI-Mode requires that the Z-Stick to be plugged into
the USB connector of the host.
• Inclusion-Mode : Adding/Including Z-Wave Devices into the Z-Wave Network
1. To initiate Inclusion-Mode, unplug the Z-Stick from the USB connector and then tap the
button. (The LED will blink slowly.)
Note: While in Inclusion-Mode, the Z-Stick is in perpetual add/inclusion. There is no
need to press the button on the Z-Stick again to include each new device.
2. To include a new Z-Wave device into the network, simply go to the device with the Z-
Stick and press the button on the device you wish to include. (The LED on the Z-Stick
will blink fast during a network neighbor discovery and stay solid for 3 seconds to
indicate successful inclusion of the device into the network.)
3. The LED will then return to blinking slowly, indicating readiness for further device
inclusions. Repeat step 2 for each device as you wish to include.
4. Tap the Z-Stick button to turn it off.
• Removal-Mode : Deleting/Removing/Excluding Z-Wave Devices from the Z-Wave Network
1. To initiate Removal-Mode, unplug the Z-Stick from the USB connector. Then press and
hold down the button for approximately 3 seconds. (The LED will transition from
blinking slowly to blinking fast.)
Note: While in Removal-Mode, the Z-Stick is in perpetual removal/exclusion where it
will remove Z-Wave devices from the networks they are currently paired to. There is no
need to press the button on the Z-Stick again to exclude each device.
2. To remove a Z-Wave device from the network, simply go to the device with the Z-Stick
and press the button on the device you wish to remove. (The LED on the Z-Stick will
immediately stay solid for 3 seconds to indicate successful removal from the network.)
3. The LED will then return to blinking fast, indicating readiness for further device
exclusions. Repeat step 2 for each device as you wish to exclude.
4. Tap the Z-Stick button to turn off.
Produktspecifikationer
| Varumärke: | Aeon Labs |
| Kategori: | Nätverkskort/adapter |
| Modell: | Z-Stick |
Behöver du hjälp?
Om du behöver hjälp med Aeon Labs Z-Stick ställ en fråga nedan och andra användare kommer att svara dig
Nätverkskort/adapter Aeon Labs Manualer
2 September 2024
Nätverkskort/adapter Manualer
- 7inova
- Satechi
- Axis
- Supermicro
- Vigitron
- Tycon Systems
- Raspberry Pi
- Simplecom
- Maxxter
- Netgear
- Konig
- Terris
- EQ-3
- Abus
- Raidsonic
Nyaste Nätverkskort/adapter Manualer
8 April 2025
3 April 2025
3 April 2025
2 April 2025
2 April 2025
1 April 2025
30 Mars 2025
29 Mars 2025
14 Mars 2025
14 Mars 2025