Amprobe ACD-6-PRO Bruksanvisning
Amprobe
Mätutrustning
ACD-6-PRO
Läs gratis den bruksanvisning för Amprobe ACD-6-PRO (15 sidor) i kategorin Mätutrustning. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 13 recensioner. Har du en fråga om Amprobe ACD-6-PRO eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/15
USER'S
MANUAL
ACD-6 Pro
ACD-6 TRMS Pro
Versatile Clamp-on
Multimeter Series
1
1) SAFETY
This manual contains information and warnings that must be followed for operating the
instrument safely and maintaining the instrument in a safe operating condition. If the
instrument is used in a manner not specified by the manufacturer, the protection
provided by the instrument may be impaired.
The meter meets the requirements for double insulation to IEC61010-2-032(1994),
EN61010-2-032(1995), UL3111-2-032(1999):
Category III 600 Volts AC and DC.
PER IEC61010 OVERVOLTAGE INSTALLATION CATEGORY
OVERVOLTAGE CATEGORY II
Equipment of OVERVOLTAGE CATEGORY II is energy-consuming equipment to be
supplied from the fixed installation.
Note – Examples include household, office, and laboratory appliances.
OVERVOLTAGE CATEGORY III
Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations.
Note – Examples include switches in the fixed installation and some equipment for
industrial use with permanent connection to the fixed installation.
OVERVOLTAGE CATEGORY IV
Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the
installation. Note – Examples include electricity meters and primary over-current
protection equipment.
TERMS IN THIS MANUAL
• WARNING identifies conditions and actions that could result in serious injury or
even death to the user.
• CAUTION identifies conditions and actions that could cause damage or
malfunction in the instrument.
2
WARNING
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture. The meter is intended only for indoor use.
To avoid electrical shock hazard, observe the proper safety precautions when working
with voltages above 60 VDC or 30 VAC rms. These voltage levels pose a potential
shock hazard to the user.
Inspect test leads, connectors, and probes for damaged insulation or exposed metal
before using the instrument. If any defects are found, replace them immediately.
Do not touch test lead tips or the circuit being tested while power is applied to the
circuit being measured. To avoid accidentally short circuit of bare (uninsulated)
hazardous live conductors or busbars, switch them off before insertion and removal of
the current clamp jaws. Contact with the conductor could result in electric shock. Keep
your hands/fingers behind the hand/finger barriers that indicate the limits of safe
access of the meter and the test leads during measurement.
CAUTION:
Disconnect the test leads from the test points before changing meter functions.
INTERNATIONAL ELECTRICAL SYMBOLS
!
!
!
!! Caution ! Refer to the explanation in this Manual
Caution ! Risk of electric shock
Earth (Ground)
Double Insulation or Reinforced insulation
Fuse
AC--Alternating Current
DC--Direct Current
2) CENELEC Directives
The instruments conform to CENELEC Low-voltage directive 73/23/EEC and
Electromagnetic compatibility directive 89/336/EEC
Produktspecifikationer
| Varumärke: | Amprobe |
| Kategori: | Mätutrustning |
| Modell: | ACD-6-PRO |
Behöver du hjälp?
Om du behöver hjälp med Amprobe ACD-6-PRO ställ en fråga nedan och andra användare kommer att svara dig
Mätutrustning Amprobe Manualer
20 Oktober 2024
26 September 2024
6 September 2024
26 Augusti 2024
20 Augusti 2024
20 Augusti 2024
15 Augusti 2024
14 Augusti 2024
14 Augusti 2024
10 Augusti 2024
Mätutrustning Manualer
- SRS
- Technics
- Homedics
- Muller
- Carrier
- VirtuFit
- IKEA
- Zircon
- BAXTER
- Arya
- TFA
- Logilink
- Pancontrol
- Black And Decker
- Motrona
Nyaste Mätutrustning Manualer
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025