Amtrol Therm-X-Trol ST-80V Bruksanvisning

Amtrol Pannor & pannor Therm-X-Trol ST-80V

Läs gratis den bruksanvisning för Amtrol Therm-X-Trol ST-80V (2 sidor) i kategorin Pannor & pannor. Guiden har ansetts hjälpsam av 23 personer och har ett genomsnittsbetyg på 4.1 stjärnor baserat på 12 recensioner. Har du en fråga om Amtrol Therm-X-Trol ST-80V eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

USE ONLY WITH RESIDENTIAL POTABLE

WATER SYSTEMS. Do not operate in a setting

with freezing temperatures or where the temperature can exceed 200°F

and do not exceed the maximum working pressure specified for this

Product. Do not use on a system with ASME-rated vessels.

READ CAREFULLY THE PRODUCT

INSTALLATION, OPERATING AND

MAINTENANCE MANUAL. FAILURE TO FOLLOW THE

INSTRUCTIONS AND WARNINGS IN THE MANUAL MAY RESULT IN

SERIOUS OR FATAL INJURY AND/OR PROPERTY DAMAGE, AND

WILL VOID THE PRODUCT WARRANTY. THIS PRODUCT MUST BE

INSTALLED BY A LICENSED PROFESSIONAL. FOLLOW ALL

APPLICABLE LOCAL AND STATE CODES AND REGULATIONS, IN

THE ABSENCE OF SUCH CODES, FOLLOW THE CURRENT

EDITIONS OF THE NATIONAL PLUMBING CODE AND NATIONAL

ELECTRIC CODE, AS APPLICABLE.

This Product, like most Products under pressure,

may over time corrode, weaken and burst or

explode, causing serious or fatal injury, leaking or flooding and/or

property damage. To minimize risk, a licensed professional must install

and periodically inspect and service the Product. Do not install this

product where leaking or flooding could cause property damage to the

area adjacent to the appliance or to lower floors of the structure.

RUPTURE OR EXPLOSION HAZARD. Do not

expose Product to freezing temperatures or

temperatures in excess of . Do not adjust the pre-charge or 200°F

re-pressure this Product except during installation or regular inspection.

Replace the Product and do not adjust the precharge if corroded,

damaged or with diminished integrity. Adjustments to pre-charge must be

done at ambient temperature only. Failure to properly size the Product or

follow these instructions may result in excessive strain on the system and

may lead to Product failure, serious or fatal personal injury, leakage and/

or property damage.

A relief valve must be installed to prevent pressure

in excess of local code requirement or maximum

working pressure designated in the Product Manual, whichever is less.

At least once every 3 years or if discharge is present, a licensed

professional should inspect the temperature and pressure relief valve

and replace if corrosion is evident or the valve does not function.

FAILURE TO INSPECT THIS VALVE AS DIRECTED COULD RESULT

IN UNSAFE TEMPERATURE OR PRESSURE BUILD-UP WHICH CAN

RESULT IN PRODUCT FAILURE, SERIOUS INJURY OR DEATH AND/

OR SEVERE PROPERTY DAMAGE AND VOID THE PRODUCT

WARRANTY.

Chlorine & Aggressive Water: The water quality

can significantly influence the life of this Product.

You should test for corrosive elements, acidity, total solids and other

relevant contaminants, including chlorine and treat your water

appropriately to insure satisfactory performance and prevent premature

failure.

This product can expose you to chemicals including

lead, which is known to the State of California to

cause cancer and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov.

THERMAL EXPANSION TANKS

FOR POTABLE WATER

INSTALLATION & OPERATION INSTRUCTIONS

Models ST-5 through ST-210V

Models T-5 and T-12

NOTE: Inspect for shipping damage and notify freight carrier or store where purchased immediately if damage is present. To avoid risk of personal

injury and property damage, if the product appears to be malfunctioning or shows signs of corrosion, call a qualified professional immediately. Current