ANT mix 24FX USB Bruksanvisning
ANT
Mixerkonsol
mix 24FX USB
Läs gratis den bruksanvisning för ANT mix 24FX USB (49 sidor) i kategorin Mixerkonsol. Guiden har ansetts hjälpsam av 19 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 10 recensioner. Har du en fråga om ANT mix 24FX USB eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/49
EN USER MANUAL | SECTION 1
IT MANUALE D’USO | SEZIONE 1
LIVE MIXING CONSOLES WITH EFFECTS & USB
MIXER LIVE CON EFFETTI & USB
TABLE DE MIXAGE LIVE AVEC EFFETS & USB
MIXER LIVE MIT EFFEKTEN & USB
MEZCLADOR LIVE CON EFECTOS Y USB
FR NOTICE D’EMPLOI | SECTION 1
DE BEDIENUNGSANLEITUNG | KAPITEL 1
ES MANUAL DE USO | SECCIÓN 1
ENGLISH
ANTMIX Series | User manual
2
3
SERIES
User manual | ANTMIX Series
1 MIC INPUT
XLR-F balanced microphone input.
2 MONO LINE INPUT - CHANNELS FROM 1 TO 8 (16FX USB) / FROM 1 TO 16 (24FX USB)
6.35 mm. (1/4”) balanced line input. You may also use an unbalanced cable.
3 STEREO LINE INPUT - CHANNELS FROM 9 TO 12 (16FX USB) / FROM 17 TO 20 (24FX USB)
Two 6.35 mm. (1/4”) balanced line input.
Connecting only one cable to L/MONO, it becomes a mono channel. You can also use an
unbalanced cable.
4 INSERT - CHANNELS FROM 1 TO 8 (16FX USB) / FROM 1 TO 16 (24FX USB)
6.35 mm. (1/4”) TRS socket. This socket allows you to connect external devices (e. g. a
compressor, an EQ, etc.) to process the signal. For this connection use a "Y" cable, plugging
to this socket a TRS connector (tip = send, ring = return, and sleeve = ground) then connect
the external device with two TS connectors, one for input and one for the output.
5 GAIN & CLIP LED
This knob adjusts the gain of the microphone or line signal, turn it to the right to raise the
level, or to the left to decrease it.
The CLIP LED is lit when the input signal is too high.
6 COMP & LED - CHANNELS FROM 1 TO 6 (16FX USB) / FROM 1 TO 8 (24FX USB)
This knob simultaneously adjusts compression threshold and ratio. Turning the knob hard left,
the compressor is turned off, turning to the right you activate it, until the maximum compression
to + 10. Use this control, for example, to make voices levels more homogeneous. The LED
next to the knob lights up when the compressor is activated.
7 LOW CUT - CHANNELS FROM 1 TO 12 (16FX USB) / FROM 1 TO 20 (24FX USB)
This switch activates the hi-pass lter to reduce the frequencies from 75Hz down.
Use it to avoid that microphones connected to the input channels will pick up unwanted
signals rich of low frequencies.
8 EQ - CHANNELS FROM 1 TO 8 (16FX USB) / FROM 1 TO 16 (24FX USB)
Use this three-band equalizer to boost or to cut the high, mid and lo frequencies to get the
best mix in any environment. The semi-parametric FREQ. control allows frequency selection
from 100Hz to 8kHz.
The warnings in this manual must be observed together with the “user manual - Section 2”.
PACKAGE CONTENT
• 1 x Mixing console
• 1 x Mains cable with VDE plug
• 1x User manual - Section 1
• 1x User manual - Section 2
TABLE OF CONTENTS
1 | Introduction 2
2 | Installation 2
3 | Description 3
3.1 | Mixer controls & connections 3
3.1.1 | Mono/stereo inputs 3
3.1.2 | Stereo Inputs 5
3.1.3 | Power supply and master section 6
3.1.4 | USB interface & applications 11
3.1.5 | Optional Bluetooth
®
& MP3 player boards 12
4 | Troubleshooting 13
5 | Technical specications 14
6 | Connectors 16
7 | System connections 17
8 | Notes 19
1 | INTRODUCTION
Thank you for choosing a A.N.T - Advanced Native Technologies - product!
In ANTMIX series of mixing consoles we have put our passion and our technological background gained over the years, to offer
products that meet your needs, and maintaining the quality over time.
All the models of this series represent a solution rich of features and optimally blend professional features with great quality and
exceptional value as: the advanced internal DSP with different effects and variations, the built-in compressor for main microphone
inputs, 60 mm faders as well as a series of I/O to fulll a wide range of applications.
Both models feature a USB port, allowing connections to a computer or a tablet.
Specically designed for an immediate and user friendly use, these mixers satisfy the needs of those who want an audio mixer
providing excellent performances, wide versatility of connections and controls as well as the best value for this range of products.
Please, dedicate some minutes to read this instruction manual in order to quickly achieve the best performances from this product.
For safety precautions, warranty and disposal, please refer to attached Section 2.
For further information about all A.N.T products catalog, please visit our website: www.ant-intomusic.com
2 | INSTALLATION
ANTMIX 16FX USB / 24FX USB models
are provided of:
A | Metal rough and light chassis.
B | ABS side panels with
ergonomic handle.
C | Front panel holes for optional boards
- MPX 1624 (MP3 player) or
BTX 1624 (Bluetooth
®
module)
3 | DESCRIPTION
3.1 | MIXER CONTROLS & CONNECTIONS
3.1.1 | MONO/STEREO INPUTS
BA C
1
2
4
3
5
6
7
BA C
8
ENGLISH
ANTMIX Series | User manual
4
5
SERIES
User manual | ANTMIX Series
9 EQ - CHANNELS FROM 9 TO 12 (16FX USB) / FROM 17 TO 20 (24FX USB)
Use this four-band equalizer to boost or to cut the high, mid and lo frequencies to get the best mix in
any environment.
10 AUX 1 & 2
These knobs adjust the signal sent to AUX SEND 1 and 2. both sends can be set pre-/post-fader.
11 AUX 1 & 2 PRE/POST
This selector determines whether the AUX 1and 2 send level is independent (PRE) or is influenced (POST)
by the channel level control. Generally it is used PRE to send the signal to stage monitors or IEM, POST
to send the signal to an external effect unit.
12 AUX 3
This post-fader send, i.e. dependent on level control of its channel, allowing to adjust the signal sent to
an external effect unit or to a monitor connected to the AUX SEND 3 output.
13 DFX POST
This send, influenced by the individual channel level control, adjusts the signal sent to the internal effects
or to an external effects connected to DFX SEND output. Furthermore, the DFX POST control can be used
as the fourth auxiliary send (deactivating the internal effect via the DFX MUTE button) for connection to
an external effects unit connected to the AUX SEND 4 output.
14 PAN - CHANNELS FROM 1 TO 8 (16FX USB) / FROM 1 TO 16 (24FX USB)
This knob adjusts the signal position in the stereo eld.
15 BAL - CHANNELS FROM 9 TO 12 (16FX USB) / FROM 17 TO 20 (24FX USB)
The BAL knob sets the left-right balance for stereo channels.
16 MUTE & LED
Press this button to mute the selected channel source.
The lit LED indicates the MUTE activation.
17 SOLO & LED
Press this button to check channel signal level before the fader.
It works also when the channel is muted; the led indicates the activation of the command.
18 GR 1-2
Press this button to route the channel signal to GROUP OUT 1-2 outputs.
19 GR 3-4
Press this button to route the channel signal to GROUP OUT 3-4 outputs.
20 L-R
Press this button to route the channel signal to MAIN MIX L-R outputs.
21 VOLUME
Use this fader to adjust overall channel volume.
22 SIG LED
This led is light when the input signal is very strong and it's close to distortion.
If the LED is continuously lit, you need to reduce the VOLUME of the fader or cut the channel EQ by
reducing the boost introduced by the HI-MID-LOW tone gains.
1 LINE L (MONO) & R INPUT
Two 6.35 mm. (1/4”) balanced line input.
Connecting only one cable to L/MONO, it becomes a mono channel. You can also use an
unbalanced cable.
2 GAIN & CLIP LED
This knob adjusts the gain of the microphone or line signal, turn it to the right to raise the
level, or to the left to decrease it.
The CLIP LED is lit when the input signal is too high.
3 LINE/USB
Press this switch to assign channels 15/16 (16FX USB) and 23/24 (24FX USB) to the USB
interface and receive the audio signal from the computer connected to the unit. In the LINE
position, key released , the channels are normally assigned to the respective inputs jack.
4 EQ
Use this four-band equalizer to boost or to cut the high, mid and lo frequencies to get the
best mix in any environment.
5 AUX 1 & 2
These knobs adjust the signal sent to AUX SEND 1 and 2. Both sends can be set pre-/post-fader.
6 AUX 1 & 2 PRE/POST
This selector determines whether the AUX 1and 2 send level is independent (PRE) or is
influenced (POST) by the channel level control. Generally it is used PRE to send the signal to
stage monitors or IEM, POST to send the signal to an external effect unit.
7 AUX 3
This post-fader send, i.e. dependent on level control of its channel, allowing to adjust the
signal sent to an external effect unit or to a monitor connected to the AUX SEND 3 output.
8 DFX POST
This send, influenced by the individual channel level control, adjusts the signal sent to the internal
effects or to an external effects connected to DFX SEND output. Furthermore, the DFX POST
control can be used as the fourth auxiliary send (deactivating the internal effect via the DFX
MUTE button) for connection to an external effects unit connected to the AUX SEND 4 output.
9 BAL
The BAL knob sets the left-right balance for stereo channels.
10 MUTE & LED
Press this button to mute the selected channel source.
The lit LED indicates the MUTE activation.
11 SOLO & LED
Press this button to check channel signal level before the fader.
It works also when the channel is muted; the led indicates the activation of the command.
3.1.2 | STEREO INPUTS
13/14 - 15/16 (ANTMIX 16FX USB) / 21/22 - 23/24 (ANTMIX 24FX USB)
9
1
2
3
4
9
10
11
5
6
7
8
14
10
11
13
12
15
16
18
19
20
22
21
17
Produktspecifikationer
| Varumärke: | ANT |
| Kategori: | Mixerkonsol |
| Modell: | mix 24FX USB |
Behöver du hjälp?
Om du behöver hjälp med ANT mix 24FX USB ställ en fråga nedan och andra användare kommer att svara dig
Mixerkonsol ANT Manualer
9 September 2024
8 September 2024
7 September 2024
6 September 2024
5 September 2024
Mixerkonsol Manualer
- Korona
- Alecto
- Roadstar
- Shure
- Santos
- Zoom
- Zelmer
- Emerio
- Alesis
- Scott
- Citronic
- IMG Stage Line
- Phonic
- Numark
- Gemini
Nyaste Mixerkonsol Manualer
2 April 2025
2 April 2025
31 Mars 2025
31 Mars 2025
31 Mars 2025
19 Mars 2025
16 Mars 2025
13 Mars 2025
13 Mars 2025