Anthro Fit Console Unit Bruksanvisning
Läs gratis den bruksanvisning för Anthro Fit Console Unit (4 sidor) i kategorin Byrå. Guiden har ansetts hjälpsam av 36 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 18.5 recensioner. Har du en fråga om Anthro Fit Console Unit eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
R
Questions?
1-800-325-3841
Anthro
Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
SAVE THESE INSTRUCTIONS!
Rev. F January 2006
Hello! Thank you for choosing Anthro.
Before beginning assembly of your Console Unit, take a moment to review the parts listed on the next page
to verify that your shipment is complete.
Please review the assembly instructions of all Anthro products you
purchased and are planning to include in this installation, prior to beginning this assembly.
Your Console Unit is heavy!
A second person will be needed for this assembly procedure.
To make the assembly of your Console Unit even easier, we have included all of the required tools. The handy
Hex Driver Bit can be used in your electric drill in place of the Hex Driver.
Hex Driver
5
/
32
”
............................................................
375-5000-00
Hex Driver Bit
5
/
32
”
.....................................................
375-5003-00
Hex Key
5
/
32
”
.................................................................
375-5016-00
Hex Key
1
/
4
”
..................................................................
375-5024-00
3-Way Wrench
.............................................................
225-5196-03
8 oz. Rubber Mallet
.....................................................
375-5022-00
Console Unit
Assembly Instructions
1-800-325-3841
Step 15
Begin by placing the Base Tube Assembly
(Locking Casters
as shown)
onto the Vertical Legs.
Attach the Base Tubes to each Leg by inserting a
fi t
Bolt through a Tube Washer, then insert the
fi t
Bolt
through the Base Tube and carefully thread into
each Vertical Leg.
Tighten all
fi t
Bolts and Cap Screws.
Step 16
(uses the
1
/
8
” Hex Key)
Carefully rotate your Console Unit onto the Casters.
Pop the six Small End Caps into the Leg ends.
Congratulations!
Your assembly is complete.
(
5
/
16
-18 X 3.5”)
fi t
Bolt
325-5194-00
fi t
Tube Washer
225-2050-00 or 225-3522-00
fi t Tube Washer
fi t Tube Washer
Locking Casters
Small End Caps
Adjust the Caddy Shelf height by:
1. Squeezing and holding the Paddle.
2. Reposition the Caddy to the desired location.
3. Release the Paddle.
Rotate Knob to
adjust Caddy
angle.
Squeeze Paddle
to adjust Caddy
height.
angle.
Adjust the Caddy Shelf angle by:
1. Rotating the Knob counterclockwise.
2. Reposition the Caddy to the desired angle.
3. Rotate the Knob clockwise.
Adjusting your Console Caddy
Produktspecifikationer
| Varumärke: | Anthro |
| Kategori: | Byrå |
| Modell: | Fit Console Unit |
Behöver du hjälp?
Om du behöver hjälp med Anthro Fit Console Unit ställ en fråga nedan och andra användare kommer att svara dig
Byrå Anthro Manualer
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
Byrå Manualer
- ThunderX3
- Ahrend
- Zaor
- Leen Bakker
- Gami
- Mount-It!
- Cougar
- Yaasa
- Bretford
- Chief
- Victor
- HJH Office
- Digitus
- Alpha Gamer
- StarTech.com
Nyaste Byrå Manualer
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025