Apricorn Velocity Duo X2 Bruksanvisning
Apricorn
Kontroller
Velocity Duo X2
Läs gratis den bruksanvisning för Apricorn Velocity Duo X2 (2 sidor) i kategorin Kontroller. Guiden har ansetts hjälpsam av 24 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 12.5 recensioner. Har du en fråga om Apricorn Velocity Duo X2 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Power-down the system and physically remove the power
cord(s) from the system.
Remove the cover from the system’s chassis, following
instructions provided by the manufacturer.
Select an available PCIe Gen 1 / Gen 2 (x2, x4, p1-x8 or x16)
slot and insert the Velocity Duo card into the slot, as shown
in Figure 1. ( p1-x2 slots are very rare in desktop NOTE:
systems, typical installation will use a p1-x4 slot).
Hold the Velocity Duo card at the edges and press down
gently into place.
Secure the Velocity Duo metal bracket to the system
chassis by tightening the slot screw.
After the Velocity Duo is installed, replace the chassis
cover, reconnect the power cord(s) and boot the computer.
Follow the directions below to complete your upgrade.
1.
2.
3.
4.
5.
6.
7.
Installing the Velocity Duo
in your desktop computer
Velocity Duo Quick Start Guide
To prevent ESD
(Electrostatic Discharge) damage
Use an ESD wrist strap or discharge static electricity by
touching a grounded bare metal surface before handling,
installing, and removing the Velocity Duo. Observe proper
ESD grounding techniques. Store your HDD or SSD in an
anti-static bag until you are ready to install it in the system.
When installing and removing the Velocity Duo Card hold by
the edge of the printed circuit board (PCB), and avoid
touching components including connectors.
IMPORTANT HANDLING INFORMATION
Connecting your SSD to the Velocity DUO Card
Slide both of your
SSDs onto the SATA
connectors on the
Velocity Duo Card. Use
4 mounting screws in
each drive to secure
them to the Duo Card.
SATA connector
SATA connector
Figure 1. Installing the Velocity Duo on
PCIe Gen 1 / Gen 2 slot
NOTE: Windows XP users and those using the Velocity
Duo with a boot disk (i.e. with OS already installed)
Before connecting your SSD to the Velocity Duo, please refer
to the directions below for installation of Windows drivers.
PCIe Gen 1/Gen 2 ( x2 slot or larger)
To ensure optimal RAID functionality, both of the SSDs on the Velocity Duo must be identical (same brand, same
firmware revision and capacity) Additionally, prior to data cloning, each drive must be eroed out using a disk utility such
as Gparted, Parted agic, or a utility native to your OS. Since RAID is strictly a performance-enhancing array with data
being striped across 2 drives, if one of those drives should fail, all data on both will be lost. When using Velocity Duo with
RAID configuration, regular backup is recommended to minimie data loss.
Produktspecifikationer
| Varumärke: | Apricorn |
| Kategori: | Kontroller |
| Modell: | Velocity Duo X2 |
Behöver du hjälp?
Om du behöver hjälp med Apricorn Velocity Duo X2 ställ en fråga nedan och andra användare kommer att svara dig
Kontroller Apricorn Manualer
2 September 2024
Kontroller Manualer
- Pearl Sports
- Gamesir
- Kanlux
- Rain Bird
- HQ Power
- Targus
- Emtec
- Apart
- Belkin
- Deltaco
- SIIG
- Novation
- Eurolite
- Akai
- Aruba
Nyaste Kontroller Manualer
21 Oktober 2025
21 Oktober 2025
21 Oktober 2025
19 Oktober 2025
18 Oktober 2025
13 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025
12 Oktober 2025