Arkon MAG1057 Bruksanvisning
Arkon
ej kategoriserat
MAG1057
Läs gratis den bruksanvisning för Arkon MAG1057 (1 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 2.5 recensioner. Har du en fråga om Arkon MAG1057 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
!
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Friday 9am - 5pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in Taiwan & China
© Copyright 2015 Arkon Resources, Inc.
The Mobile Mounting Specialists™
Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsibility
of liability for injury or death as a result of car crashes and / or air bag
deployment.
Arkon is not responsible for any damages caused to your vehicle, your
device, or yourself due to the installation or use of this mount.
Package Contents:
(1) GN057 - Removable 17mm Ball Air Vent Mount
(1) GN010 - Adhesive Dash or Console Mount
(1) SP-MAGKIT - Magnet Head with Adjustment Ring and Adhesive Metal Plates
NOTE: Not compatible with round air vent louvers.
Do not place console mount in or near an air bag deployment zone
or where it will obstruct view of the road.
To attach console mount, fi nd a fl at area on the console or dash-
board. Clean the surface with the included alcohol pad and let dry.
Remove paper backing on the adhesive console mount. Press and
hold the mount on the console or dash surface for about a minute.*
57
SP-MAGKIT
GN010
GN
05
1
To attach magnet head, slide ring over 17mm ball. Adjust angle
and tighten adjustment ring to secure.
2
To attach air vent mount, squeeze clip to open and insert into air
vent louvers.
Adjust lower support leg.
Pedestal Clip
Pedestal Clip
Pedestal Clip
Pedestal Clip
Pedestal Clip
Support
Support
Support
Support Support
Leg
Leg
Leg
Leg
Leg
43
Remove paper backing of adhesive metal plate. Firmly press the ad-
hesive side to clean, back surf
ace of your smartphone or case. Place
metal plate on smartphone in contact with magnet head on air vent
or console mount to attach. Rotate or adjust angle as needed.
!
*Let mount adhesive
*Let mount adhesive
*Let mount adhesive
*Let mount adhesive
*Let mount adhesive
set for 2
set for 2
set for 2
set for 24 hours at room
4 hours at room
4 hours at room
4 hours at room
set for 24 hours at room
temp. (72º F) before use.
temp. (72º F) before use.
temp. (72º F) before use.
temp. (72º F) before use.temp. (72º F) before use.
(Smartphone
(Smartphone
(Smartphone
(Smartphone (Smartphone
not included,
not included,
not included,
not included, not included,
sold separately)
sold separately)
sold separately)
sold separately)sold separately)
Metal
Metal
Metal
Metal Metal
Plate
Plate
Plate
PlatePlate
Adjustment
Adjustment
Adjustment
Adjustment Adjustment
Ring
Mag
Mag
Mag
Magne
ne
ne
net
t
t
t Magnet
Head
Head
Head
Head
Head
Adjustment Ring
a
e
Ma
gn
et
MAG1057 | Air Vent and Adhesive Console or Dash Magnet Mount Bundle
rev.011615
Produktspecifikationer
| Varumärke: | Arkon |
| Kategori: | ej kategoriserat |
| Modell: | MAG1057 |
Behöver du hjälp?
Om du behöver hjälp med Arkon MAG1057 ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Arkon Manualer
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
ej kategoriserat Manualer
- Hansgrohe
- Aspes
- Trisa
- Denon
- Uni-T
- Vivo
- ORNO
- IKEA
- MSI
- Lasko
- Joy-it
- Aiphone
- Teslong
- Audio-Technica
- AMX
Nyaste ej kategoriserat Manualer
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025