Artecta Ribbon Bruksanvisning

Artecta Inte kategoriserad Ribbon

Läs gratis den bruksanvisning för Artecta Ribbon (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 31 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 16 recensioner. Har du en fråga om Artecta Ribbon eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

1. Product Description

2. Safety Instructions

Important

Read and follow the instructions in this user manual

before installing, operating or servicing this product.

User Manual

The Ribbon Series are IP20 LED strips for indoor installation at dry

places. They are suitable for mounting in an aluminum prole. The

Ribbon Series are available in various color temperatures and as

RGB, RGBW and RGBA options.

For complete product specications visit the respective product

page on our website .www.highlite.com

Ribbon

Series

This product must be installed in accordance with the applicable

national and international standards for electrical installations.

Improper installation may lead to hazardous situations and

material damage.

DANGER

Installation, service and maintenance of this product

shall be carried out only by qualied persons.

3. Installation Site Requirements

Attention

The LED strips are suitable for installation only in dry

locations. Not suitable for outdoor installation.

Do not install the LED strips:

in wet locations

at a place where the LED chips are exposed to direct sunlight

near heat-generating devices.

Do not install the LED strips in environments with highly volatile

substances, such as sulfur, chlorine, bromine and VOC. This will

reduce the life of the LED chips.

Make sure that the LED strips are installed at a place with:

ambient temperature between -20 °C and 50 °C

sufcient airow.

Make sure that the mounting surface is clean and smooth, and

free of grease or silicone oil.

Make sure that the mounting surface is thermally conductive and

provides good heat dissipation.

If the LED strips are mounted on a metallic surface, make sure that

the soldering points are insulated. If the soldering points are not

insulated, short-circuit may occur.

No part of this document may be copied, published or

otherwise reproduced without the prior written consent of

Highlite International.

Design and product specications are subject to change

without prior notice.

For the latest version of this document and other language

versions, please visit our website or www.highlite.com

Highlite International B.V. • Vestastraat 2 • 6468 EX • Kerkrade • the Netherlands

4. Handling

Do not connect the LED strip to

electrical power supply when

the LED strip is on the reel or

when it is tightly coiled. This will

damage the LEDs.

Do not put excessive pressure

on the LED chips.

Do not fold or break the LED

strips.

Do not cover the LED strips with

any material during operation.

You can bend the LED strip only

along the vertical axis. The

minimum bending radius is

20mm.

Do not bend the LED strip with

the LEDs on the inside.

20 mm

Do not bend the LED strip on the

horizontal plane.

Do not twist the LED strip.

It is recommended to install the LED strips in an aluminum prole.

An aluminum prole provides good heat dissipation.

Produktspecifikationer

Varumärke:	Artecta
Kategori:	Inte kategoriserad
Modell:	Ribbon
Färg på produkten:	Zwart
Impedans:	8 Ohm
Medium effekt subwoofer:	700 W
Diameter drivrutin subwoofer (imperiaal):	18 "
Subwoofertyp:	Actieve subwoofer
Subwooferns frekvensområde:	33 - 3000 Hz
Subwooferns bredd:	610 mm
Höjd på subwoofern:	591 mm
Subwooferns djup:	709 mm
Vikt subwoofer:	44000 g
Trådlös subwoofer:	Nee
Subwooferkänslighet:	96 dB
Antal subwoofers:	1
Diameter drivrutin för subwoofer:	460 mm
Subwoofer maximal effekt:	2800 W