Asus ROG Chariot Core Bruksanvisning
Asus
Inte kategoriserad
ROG Chariot Core
Läs gratis den bruksanvisning för Asus ROG Chariot Core (5 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 8 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 4.5 recensioner. Har du en fråga om Asus ROG Chariot Core eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/5
SL300 ROG Chariot core Installation Guide
Package Contents
A
Installing the Lumbar cushion
C
Other features
E
Assembling your chair
B
Put on the gloves before installation.
One by one, insert and push the wheels into the
base.
Insert the hydraulic lift cylinder into the center
hole of the base. Remove the red protective cap
on top if there was any.
Place the telescoping cover on the top of the
hydraulic lift cylinder.
Armrests normally do not
distinguish sides unless labeled
otherwise.
For models with armrest pre-
assembled, please skip this step.
Remove the pre-assembled bolts and washers
(1 & 3). Place the 4 large washers ( 1)
between the armrest mounting bar ( 2) and the
seat base. Hold the armrest in place, then insert
and tighten all 4 bolts ( 3). Use the hex key to
tighten them all, and repeat on the other side.
Use the hex key to remove the pre-assembled
bolts and washers from the backrest.
Remove the protective foam covers from the
brackets of the seat base. Then position the
backrest carefully between the brackets. Insert
and attach the 4 bolts (2 on each side) you
removed in step 5 by hand rst. Then use the hex
key to tighten them. Start with the two bolts on
the top of each side, then the bottom two.
E15376 / First Edition / July 2019
Note: The illustrations are for reference only and may dier from your actual
chair in appearance and features.
Install the side covers and tighten the bolts. (The
covers are marked “L” for the left side and “R” for the
right on the inside.)
Now ip the chair over, facing down. Then remove
the 4 pre-mounted bolts from the underside with
washers.
Repeat the step above to install the control
unit, and then place the nut to mount the
hydraulic lift cylinder facing the back of the
seat (where the backrest is installed).
Insert top of the hydraulic lift cylinder into the
mounting hole on the control unit, and then turn
the chair over in upright position. (Two-person
handling required for your safety)
The chair and the Lumbar cushion are designed with Velcro fasteners.
Attach the Lumbar cushion to the chair using the Velcro fasteners.
Hanger at the back of the chair for hanging
your bags, clothes, cups and more.
Maximum load: 2kg
Please do not hang items over 2kg.
1. Backrest 5. Wheels 9. Hydraulic lift cylinder
2. Seat base 6. Side covers with bolts 10. Telescoping cover
3. Lumbar cushion 7. Control unit 11. Hex Key
4. Wheel base 8. Gloves 12. Spare bolt
Produktspecifikationer
| Varumärke: | Asus |
| Kategori: | Inte kategoriserad |
| Modell: | ROG Chariot Core |
Behöver du hjälp?
Om du behöver hjälp med Asus ROG Chariot Core ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Asus Manualer
2 April 2025
2 April 2025
1 April 2025
30 Mars 2025
27 Mars 2025
5 Mars 2025
27 Februari 2025
27 Februari 2025
22 Februari 2025
8 Januari 2025
Inte kategoriserad Manualer
- Citronic
- Panduit
- Sanitas
- Xvive
- Ixxat
- IOptron
- Swedish Posture
- Mr Steam
- RCS
- Digital Juice
- Ion
- Mr. Beams
- Arturia
- Adam Hall
- Gossen Metrawatt
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025