Behringer 112 Dual VCO Bruksanvisning
Behringer
Synthesizer
112 Dual VCO
Läs gratis den bruksanvisning för Behringer 112 Dual VCO (9 sidor) i kategorin Synthesizer. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 13 recensioner. Har du en fråga om Behringer 112 Dual VCO eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/9
Quick Start Guide
(EN) Controls
(1) PW MOD IN - Accepts a voltage from another module
to control the pulse width.
(2) VCO OUT - Send the VCO signal to one or two sources
via 3.5 mm TS cables.
(3) WAVEFORM - Select pulse, triangle or sawtooth
waveforms for the VCO.
(4) PULSE WIDTH - Adjusts the pulse width modulation
based on the voltage received at the PW MOD IN jack.
(5) MOD MANUAL - Sets the ratio between the upper
and lower portions of the pulse wave.
(6) SYNC OUT - Sends a synchronization signal
via 3.5 mm TS cable.
(7) RANGE - Sets the pitch range of the VCO in octave steps.
(8) SYNC IN - Accepts a synchronization signal
via 3.5 mm TS cable.
(9) WEAK/STRONG - Determines the accuracy
of synchronization.
(10) PITCH - Fine tunes the pitch.
(3)
(4)
(1) (2)
(12)
(10)
(11)
(5)
(6)
(7)
(8)
(9)
(11) MOD LEVEL - Adjusts the level of the signal connected
to the associated MOD IN jack.
(12) MOD IN - Accepts voltages that control or modulate
the VCO pitch.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make these
connections before the module has been mounted into a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting in a
Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes spaced
2 HP apart along the length of the case, or a track that allows individual
threaded plates to slide along the length of the case. The free-moving
threaded plates allow precise positioning of the module, but each plate
should be positioned in the approximate relation to the mounting
holes in your module before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned. After
the nal position has been established, tighten the screws down.
V 1.0
112 DUAL VCO
Legendary Analog Dual VCO
Module for Eurorack
Produktspecifikationer
| Varumärke: | Behringer |
| Kategori: | Synthesizer |
| Modell: | 112 Dual VCO |
Behöver du hjälp?
Om du behöver hjälp med Behringer 112 Dual VCO ställ en fråga nedan och andra användare kommer att svara dig
Synthesizer Behringer Manualer
3 Januari 2025
3 Januari 2025
3 Januari 2025
3 Januari 2025
1 Januari 2025
14 December 2024
2 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
Synthesizer Manualer
- 2hp
- Pioneer
- Native
- Meebleeps Machines
- Future Retro
- AAS
- Kodamo
- Noise Engineering
- Nystrom
- Vermona
- MFB
- Fred's Lab
- GS Music
- Boss
- Dnipro
Nyaste Synthesizer Manualer
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025