Behringer 297 Dual Portamento/CV Utilities Bruksanvisning
Behringer
Synthesizer
297 Dual Portamento/CV Utilities
Läs gratis den bruksanvisning för Behringer 297 Dual Portamento/CV Utilities (2 sidor) i kategorin Synthesizer. Guiden har ansetts hjälpsam av 32 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 16.5 recensioner. Har du en fråga om Behringer 297 Dual Portamento/CV Utilities eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
V 1.0
Quick Start Guide
SYSTEM 100
297 DUAL PORTAMENTO/
CV UTILITIES
Legendary Analog Portamento
Controller and CV Utilities for Eurorack
Controls
(1) MIXER SIG IN – Connect incoming signals via 3.5 mm
TS cables. Inputs 3 and 4 feed +10/-10 V respectively to
the mixer inputs if no jack is inserted, which can be used
to oset the overall mixer output control voltage.
(2) PORTA SIG OUT – Send the portamento signal to another
module via 3.5 mm TS cable.
(3) PORTA SIG IN – Connect a signal to the portamento
section via 3.5 mm TS cable.
(4) SIG LEVEL – Adjust the level of the signals connected to
the mixer inputs.
(5) INV OUT – Send the mix of inputs 1-4 as an
inverted signal.
(6) NON INV OUT – Send the mix of inputs 1-4 as a
non-inverted signal.
(7) TIME – Adjust the portamento time.
(8) CV IN – Connect a voltage to control the portamento time
from another module.
(9) +10/-10 V LEVEL – Adjust the level of the +10 V and
-10 V outputs.
(10) +10/-10 V OUT – Send the +10 V and -10 V signals via
3.5 mm TS cable.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
(1)
(4)
(5)
(6)
(3)(2)
(7)
(8)
(10)
(9)
Produktspecifikationer
| Varumärke: | Behringer |
| Kategori: | Synthesizer |
| Modell: | 297 Dual Portamento/CV Utilities |
Behöver du hjälp?
Om du behöver hjälp med Behringer 297 Dual Portamento/CV Utilities ställ en fråga nedan och andra användare kommer att svara dig
Synthesizer Behringer Manualer
3 Januari 2025
3 Januari 2025
3 Januari 2025
3 Januari 2025
1 Januari 2025
14 December 2024
2 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
Synthesizer Manualer
- MFB
- Novation
- Vermona
- 2hp
- Casio
- Dnipro
- Arturia
- Roland
- ELTA Music
- Kodamo
- Majella
- Flame
- Native
- GS Music
- LennarDigital
Nyaste Synthesizer Manualer
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025