Behringer 902 Voltage Controlled Amplifier Bruksanvisning
Behringer
Synthesizer
902 Voltage Controlled Amplifier
Läs gratis den bruksanvisning för Behringer 902 Voltage Controlled Amplifier (11 sidor) i kategorin Synthesizer. Guiden har ansetts hjälpsam av 19 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 10 recensioner. Har du en fråga om Behringer 902 Voltage Controlled Amplifier eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/11
Quick Start Guide
Controls
(1) CONTROL MODE (LIN/EXP) rocker switch toggles
between linear and logarithmic response modes.
(2) FIXED CONTROL VOLTAGE knob allows you to manually
set a control voltage.
(3) SIG IN input jacks accept audio and control signals over
cables with 3.5 mm TS connectors. These dual inputs
allow the unit to amplify two signals simultaneously.
(4) SIG OUT output jacks send out amplied audio and control
signals over cables with 3.5 mm TS connectors.
(5) CONTROL INPUTS accept control voltage signals from
other modules to change the amplication level.
(1)
(3)
(2)
(4)
(5)
Power Connection
The 902 VCA comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these steps
to connect power to the module. It is easier to make these
connections before the module has been mounted into a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the
red stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded plate.
Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned.
After the nal position has been established, tighten the
screws down.
902 VOLTAGE
CONTROLLED AMPLIFIER
Legendary Analog VCA Module
for Eurorack
V 1.0
Produktspecifikationer
| Varumärke: | Behringer |
| Kategori: | Synthesizer |
| Modell: | 902 Voltage Controlled Amplifier |
Behöver du hjälp?
Om du behöver hjälp med Behringer 902 Voltage Controlled Amplifier ställ en fråga nedan och andra användare kommer att svara dig
Synthesizer Behringer Manualer
3 Januari 2025
3 Januari 2025
3 Januari 2025
3 Januari 2025
1 Januari 2025
14 December 2024
2 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
Synthesizer Manualer
- Synamodec
- IK Multimedia
- Fred's Lab
- Majella
- Native
- Arturia
- Korg
- AAS
- Studiologic
- Dnipro
- Vermona
- Sonicware
- LennarDigital
- Elektron
- Roland
Nyaste Synthesizer Manualer
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025