Behringer CP3A-M Mixer Bruksanvisning
Behringer
Synthesizer
CP3A-M Mixer
Läs gratis den bruksanvisning för Behringer CP3A-M Mixer (11 sidor) i kategorin Synthesizer. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 8 recensioner. Har du en fråga om Behringer CP3A-M Mixer eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/11
Quick Start Guide
(EN) Controls
(1) CHANNEL INPUTS connect the incoming signals
via cables with 3.5 mm TS connectors.
(2) CHANNEL GAIN knobs adjust the input volume
for the CHANNEL INPUTS.
(3) MULTIPLE connections act as a patchbay so that copies
of the input signals can be routed out to other modules
for further processing.
(4) OUTPUTS connections send out the mixer module’s
nal, summed signal. The OUTPUTS section
features two sets of output jacks with negative
and positive polarity.
(5) MASTER GAIN controls the nal volume
at the OUTPUTS jacks.
(1)
(3)
(4)
(5)
(2)
Power Connection
The CP3A-M MIXER comes with the required power cable
for connecting to a standard Eurorack power supply system.
Follow these steps to connect power to the module. It is easier
to make these connections before the module has been
mounted into a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track
that allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned
in the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the nal position has been established,
tighten the screws down.
CP3A-M MIXER
Legendary Analog Mixer/Utility Module
for Eurorack
V 1.0
Produktspecifikationer
| Varumärke: | Behringer |
| Kategori: | Synthesizer |
| Modell: | CP3A-M Mixer |
Behöver du hjälp?
Om du behöver hjälp med Behringer CP3A-M Mixer ställ en fråga nedan och andra användare kommer att svara dig
Synthesizer Behringer Manualer
3 Januari 2025
3 Januari 2025
3 Januari 2025
3 Januari 2025
1 Januari 2025
14 December 2024
2 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
Synthesizer Manualer
- Nystrom
- Omnitronic
- AAS
- Casio
- Korg
- Pioneer
- Boss
- GS Music
- Dreadbox
- Yamaha
- 2hp
- Make Noise
- Arturia
- Majella
- Soma
Nyaste Synthesizer Manualer
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025