Behringer System 55 903A Random Signal Generator Bruksanvisning
Behringer
Synthesizer
System 55 903A Random Signal Generator
Läs gratis den bruksanvisning för Behringer System 55 903A Random Signal Generator (2 sidor) i kategorin Synthesizer. Guiden har ansetts hjälpsam av 14 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 7.5 recensioner. Har du en fråga om Behringer System 55 903A Random Signal Generator eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Quick Start Guide
903A RANDOM
SIGNAL GENERATOR
Legendary Analog Noise Generator
Module for Eurorack
Outputs
Send a pair of white and/or pink noise signals to other modules via
3.5 mm TS cable.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these steps to
connect power to the module. It is easier to make these
connections before the module has been mounted into a
rack case.
(1) Turn the power supply or rack case power o and
disconnect the power cable.
(2) Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the
red stripe on the cable.
(3) Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with
the socket for correct orientation.
(4) After both ends of the power cable have been securely
attached, you may mount the module in a case and turn
on the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded plate.
Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned.
After the nal position has been established, tighten the
screws down.
Produktspecifikationer
| Varumärke: | Behringer |
| Kategori: | Synthesizer |
| Modell: | System 55 903A Random Signal Generator |
Behöver du hjälp?
Om du behöver hjälp med Behringer System 55 903A Random Signal Generator ställ en fråga nedan och andra användare kommer att svara dig
Synthesizer Behringer Manualer
3 Januari 2025
3 Januari 2025
3 Januari 2025
3 Januari 2025
1 Januari 2025
14 December 2024
2 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
Synthesizer Manualer
- Fred's Lab
- Dreadbox
- GS Music
- Synamodec
- Boss
- Future Retro
- Moog
- Casio
- Arturia
- Sequential
- Noise Engineering
- ELTA Music
- Cre8audio
- Omnitronic
- Modal Electronics
Nyaste Synthesizer Manualer
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025
19 Mars 2025