Black Box LPJ001A-T Bruksanvisning
Sidor 2 Engels Nätverkskort/adapter
Läs bruksanvisningen för Black Box LPJ001A-T gratis online eller ladda ner PDF:en. 32 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
Exceeds the 802.3at standard.
Use with IP telephones, wireless access
points, IP print servers, IP cameras,
and Bluetooth® access points.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) •
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 •
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 •
Web site: www.blackbox.com • E-mail: info@blackbox.com
Customer
Support
Information
LPJ001A-T
802.3at PoE Gigabit Injector, 1-Port
1. Specifications
Compliance: cUL/UL®; RoHS
Load (Maximum): 0.60 A
Regulation: Line and load: 54–57 VDC under all
conditions
Connectors: Data in: (1) RJ-45 (10/100/1000);
Data/PoE out: (1) RJ-45 (10/100/1000);
Power: (1) IEC 320 (3-pin)
Indicators: (3) LEDs: (1) ON, (1) PoE PLUS, (1) CONNECT
Power:AC input voltage range: 90–264 VAC;
AC input voltage rating: 100–240 VAC, 47–63 Hz;
Output: 33.6 W at 56 VDC
Size: 1.4"H x 2.6"W x 5.5"D (1 x 6.6 x 14 cm)
Weight: 0.4 lb. (0.2 kg)
2. Overview
The LPJ001A-T is a high-powered Gigabit power injector
that conforms to the IEEE 802.3at power standard.
As defined in 2009, this standard allows for a minimum
of 25 W of power to operate with PoE equipment over
a single Ethernet cable.
Use the LPJ001A-T with IP telephones, wireless access points, IP print
servers, IP cameras, and Bluetooth access points.
3. Setting Up Your Power Injector
NOTE: Use CAT5e or higher Ethernet cables (not included).
1. Using screws, affix the metal feet on the front and/or rear to a
flat surface such as a table or wall. See Figure 1.
NOTE: The power injector should not use the weight
of the Ethernet cables for support.
Figure 1. Location of metal feet on the power injector.
Power and Data in
data out
Front panel.
IEC-320 power connector.
Back panel.
Figure 2. Ports on the power injector.
2. Connect the 3-pin IEC320 AC input connector to a
power source. Power on the injector.
3. Using CAT5e or higher cable, connect the RJ-45 port
on the injector labeled “IN” to your network switch.
See Figures 2 and 3.
4. Connect the RJ-45 port labeled “OUT” on the injector over
Ethernet cable to the powered device. See Figures 2 and 3.
5. The LEDs will light to diagnose the connection. See Tables 1
and 2.
Insert a screw to
secure the unit
to a surface
Insert a screw
to secure the unit
to a surface
Produktspecifikationer
| Varumärke: | Black Box |
| Kategori: | Nätverkskort/adapter |
| Modell: | LPJ001A-T |
Behöver du hjälp?
Om du behöver hjälp med Black Box LPJ001A-T ställ en fråga nedan och andra användare kommer att svara dig
Nätverkskort/adapter Black Box Manualer
Black Box DCX3000-DVT Bruksanvisning Black Box LPR1111 Bruksanvisning Black Box ACX1MR-U23-SM Bruksanvisning
Alla Black Box Nätverkskort/adapter manualer
Nätverkskort/adapter Manualer
Nyaste Nätverkskort/adapter Manualer
StarTech.com PCMACLINK2 Bruksanvisning StarTech.com PEX1000SFP Bruksanvisning StarTech.com ST2GPEX Bruksanvisning StarTech.com USB56KEM2 Bruksanvisning StarTech.com PUSBADAP Bruksanvisning StarTech.com USB150WN1X1W Bruksanvisning Apc APVS9602 Bruksanvisning StarTech.com PCMACLINK Bruksanvisning NUVO NV-SUBRX Bruksanvisning NUVO NV-SUBTXRX Bruksanvisning