Blaupunkt DC-S3 Bruksanvisning
Blaupunkt
övervakningskamera
DC-S3
Läs gratis den bruksanvisning för Blaupunkt DC-S3 (2 sidor) i kategorin övervakningskamera. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 13 recensioner. Har du en fråga om Blaupunkt DC-S3 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Door/Window and Shutter Detector with Wire Input (DC-S3)
P
Pa
ar
rt
ts
s
D
De
es
sc
cr
ri
ip
pt
ti
io
on
n
1. LED indicator & Learn/Test Button
Press the button to transmit a learn/test code and enter Test
mode for 3 minutes. The LED will light up whenever the Detector
is activated der Test mode.un
2. Mounting Holes (Covered by White Caps)
3 Wire Input Terminial 1 .
Connect the terminal to any Normal Close (N.C) device
4. Wire Input Terminial 2
Connect the terminal to Roller Shutter
5. Jumper Switches
For Jumper Switch functions, refer to later section “Jumper
Switch Setting”.
6 Battery Insulator .
7. Tamper Switch
8. Knockout for Extension Terminals
9. Rib-Mark
10. Magnet
P
Pa
ac
ck
ka
ag
ge
e
C
Co
on
nt
te
en
nt
t
1 x Door Contact
2 x wall plugs and screws
1 x adhesive pads
1 x 3V lithium battery (pre-installed)
.
Put the Control Panel into learning mode, then press the learn
button to transmit learn code. Please refer to Control Panel
manual to complete learn in process.
The Detector can be used either as a door/ window sensor or
transmitter for shutter or wired device, or all at the same time.
Choose the mounting location according to the Door Contact’s
usage.
As a Door/window sensor: mount the main body on the
door/window frame, and the magnet on the door/window.
Mount as high as possible.
As a transmitter for shutter or wired device: mount close
to the device accordingly.
Do not mount on metallic surface.
1. Remove the white caps covering the 2 mounting holes.
2. Drill holes into the mounting location using the holes as
template.
3. Screw the sensor onto the wall or door/window frame with the
screws and plugs provided.
As a Door/ Window Sensor
4. Align the magnet with the Rib Mark on main body; screw the
magnet onto the door/window or apply with double-side
adhesive tape. The gap between the body and the magnet
should be no more than 15 mm.
As a Transmitter
5. Break through the knockout at top of the cover
6. For general wired device: connect the wire from device to
Wire Input Terminal . Multiple wired devices can be 1
connected to single Door Contact as long as the devices form
a closed loop with the Detector (Figure A)
7. For roller shutter: connect the wire from roller shutter to Wire
Input Terminal 2. (Figure B)
Figure A Figure B
8. Replace the white caps.
L
Le
ea
ar
rn
ni
in
ng
g
IInnssttaallllaattiioonn
Frame
Door/
Window
Produktspecifikationer
| Varumärke: | Blaupunkt |
| Kategori: | övervakningskamera |
| Modell: | DC-S3 |
Behöver du hjälp?
Om du behöver hjälp med Blaupunkt DC-S3 ställ en fråga nedan och andra användare kommer att svara dig
övervakningskamera Blaupunkt Manualer
4 Oktober 2024
3 Oktober 2024
18 September 2024
23 Augusti 2024
21 Augusti 2024
21 Augusti 2024
19 Augusti 2024
18 Augusti 2024
15 Augusti 2024
14 Augusti 2024
övervakningskamera Manualer
- ClearView
- Atlona
- Zavio
- Arecont Vision
- ETiger
- Niceboy
- Canyon
- Summer Infant
- EKO
- Chuango
- Strong
- August
- Denver
- Alpine
- Epcom
Nyaste övervakningskamera Manualer
23 Oktober 2025
20 Oktober 2025
20 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
18 Oktober 2025
14 Oktober 2025
14 Oktober 2025