Boyo VTL17LTJ Bruksanvisning

Läs gratis den bruksanvisning för Boyo VTL17LTJ (10 sidor) i kategorin Dashcam. Guiden har ansetts hjälpsam av 23 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 3 recensioner. Har du en fråga om Boyo VTL17LTJ eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

II. Specifications

SENSORPC 8105

Effective Pixel×297659

Viott1.0 vp, 75 Ohm-pdeou pu

VerticalSync Frcyequen

Scing System2 : 1 Interlaceann

Sync StemInterlysna

AGC Auto

BLC Auto

Resolution0 TV Lis70ne

S/N RatioMore TnBha48d

Cut CsumptionNo MoremArrenon150

DC12V ±%10

-°° F22~176

-°40 ~176° F

Power Slyupp

Operating Temperature

Storage Temperature

Viewing Aleng170°

Wate Prfr-oo

Minum Iumiimllnation

IP68

0.x/F1.2(x with LED)5Lu0Lu

III. Installation

1Finsuitle location to surfacet install the cra.ke sure the) d aabmounameMa

cra’s view isstructedd be careful not to drill intoy wires tt mightameunobananha

damagehonnebeemadanbee the vicle. When all cctions havenedfore

mounameamewoanhagooting the cra, verify the cra isrkingdsd view of the

ar. Tnt the cran with the supplied twors.eahemounamedowsc ew

2)Conctthe REDre to the +12 volt reverserenewiwi

5)Run video clethoh vehicle, up to video.(Avoid placingabugmonitor

vio cable wre it cantpinched ormed).dehegedaag

6)Aach the YELLOW video rctta to the reverse camera iut of the radio ornp

video;cnect the REDre coming from the YELLOW video rcamonitoronwi

to the reverse triggerre onthe radio or vio.widemonitor

NOTE: The camera comesth tsme view active.wirajectory neliand a mirror iag

If you wt to remove therkings or chae the ime to reverse image,anpalinengag

follow the steps below:

A)Disconnect power to the camera.

B)

C)

Cut the BLUE loop to remove the trajectory parking lines , isolate and tape the wires.

Cut the WHITE loop to get normalimage,isolate and tape the wires.

.

D)Reconnect power to the camera.

If ts areed or the imeds to gock tohe trajectory parking lineneedagneeba

reverseepabanon, just foow the stllsoved recnect the wires.

For any technical support, contact 888-941-3060 or email info@visiontechamerica.com

WWW.VISIONTECHAMERICA.COM

VTL17LTJ

Concealed Mount License Plate Camera with LED Lights/

Trajectory Parking Lines

I.Bill of Materials

Camera 24ft 4mini pin ware harness(1pcs)User manual(1pcs)Warranty Card(1pcs)Registration Card(1pcs)

Screw x2(KM6X24)

Screw x2(Pm3x10X7)

Screw x2(Pm2.5x8)

Conversionconnectorx1

Bracketx1

3M double stickerx1

NTSC 60HZ

3) Connect the BLACK wire to Chassis ground (a metal , non-painted surface).

4) Connect the GREEN wire to the + 12V volt reverse wire.

Control Wires

Blue Loop: cut = turns off trajectory lines

White Loop: cut = display non-mirror images

Green wire: connect to reverse backup light

positive = LED will turn on whenever backup

light is on.

** Monitor trigger ** when reverse backup light comes

on it will trigger the monitor to switch to backup camera.

Produktspecifikationer