BTI Aqua-Solutions FL1000 Bruksanvisning
BTI Aqua-Solutions
Vattenfilter
FL1000
Läs gratis den bruksanvisning för BTI Aqua-Solutions FL1000 (2 sidor) i kategorin Vattenfilter. Guiden har ansetts hjälpsam av 33 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 17 recensioner. Har du en fråga om BTI Aqua-Solutions FL1000 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
FILTRATION SYSTEM INSTALLATION INSTRUCTIONS
ITEM FL1000
www.btiaquasolutions.com
REV / /1811 19
Remove mounting-bracket from
Filtration System Head. Select “Snap
Fit” (two outside screws) or “Rotary”
(one center screw) bracket mounting.
The “Rotary” bracket mounting should
be used if varying positions of
Filtration System is required in cabinet.
SPECIFICATIONS
• NSF/ANSI 42 & 53 CERTIFIED
• 0.5 MICRON CARBON-BLOCK FILTER
• .55 US GAL/2.1L GPM FLOW RATE
• 1500 US GAL/5,678 L CAPACITY
• 3-STAGE FILTER
• 3” x 11” SPACE SAVING DESIGN
• BUILT-IN PRV
• SQC HEAD
• ECO-FRIENDLY, RECYCLABLE
TOOLS REQUIRED:
PENCIL, SCREWDRIVER
TO VIEW INSTALLATION VIDEO VISIT
www.btiaquasolutions.com
1 2
Measure and mark screw hole(s) for
your desired lter location.
Make sure “Location-Lug” on bracket
is on top.
3
A
Position Filtration System with label and
black location arrow facing you.
Push the lter head into bracket until you
feel it click into place.
It will only t one way, with label and
black location arrow facing you.
4
Push one end of tubing (F) into angle shut-
off valve (D). Push other end of tubing into
“L-Fitting”, pre-installed in the “inlet” on top
of lter.
Push one end of tubing (F) into “outlet”
connector on top of lter. Connect other end
of tubing to faucet-stem of ltration faucet.
If using a BTI Filtration Faucet, all items for
connection are supplied with faucet.
To remove a tube, push down on the collet
while pulling on the tube.
Turn on the water supply and check for
leaks. Flush at least one gallon of water
through the system before use. Write the
installation and lter change dates on the
label for future reference.
Location-Lug
NOTE: If using with a BTI
Hot/Cold Filtration Faucet, skip to Step 5.
Install angle shut-off valve (D) supplied with
BTI Filtration System.
Shut-off cold-water supply (E). Disconnect
line/hose (C) to kitchen faucet from cold-water
supply shut-off valve (E).
Connect angle shut-off valve (D) to cold-water
supply shut-off valve (E). Connect line/hose
from kitchen faucet (C) to angle shut-off valve
(D).
Cut the 1/4” O.D. inlet/outlet tubing (supplied)
to the correct lengths, ensuring the cut ends
are square and clean.
(A) FILTRATION FAUCET
(B) BTI FILTRATION SYSTEM
(C) LINE/HOSE TO KITCHEN FAUCET
(D) ANGLE SHUT-OFF VALVE (supplied)
(E) COLD-WATER SUPPLY SHUT-OFF VALVE
(F) 1/4” O.D. TUBING (supplied)
B
C
D
E
F
F
FILTRATION SYSTEM INSTALLATION WITH COLD ONLY FILTRATION FAUCET
Produktspecifikationer
| Varumärke: | BTI Aqua-Solutions |
| Kategori: | Vattenfilter |
| Modell: | FL1000 |
Behöver du hjälp?
Om du behöver hjälp med BTI Aqua-Solutions FL1000 ställ en fråga nedan och andra användare kommer att svara dig
Vattenfilter BTI Aqua-Solutions Manualer
31 Mars 2025
31 Mars 2025
Vattenfilter Manualer
- LG
- Billi
- Philips
- Juwel
- Grohe
- Franke
- Astralpool
- ZeroWater
- Platypus
- BWT
- Aquasure
- Aqua Medic
- Hydor
- Ionmax
- T.I.P.
Nyaste Vattenfilter Manualer
29 Mars 2025
27 Februari 2025
21 Februari 2025
8 Februari 2025
1 Februari 2025
6 Januari 2025
1 Januari 2025
31 December 2025
28 December 2024
27 December 2024