Buffalo TS4400D Bruksanvisning
Läs gratis den bruksanvisning för Buffalo TS4400D (4 sidor) i kategorin Server. Guiden har ansetts hjälpsam av 6 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 3.5 recensioner. Har du en fråga om Buffalo TS4400D eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
The TS4000 series will not work without disks. Please prepare 1 or more un-partitioned
HDDs for the setup process. Use either new HDD(s) or delete all partitions (and
therefore all data) with a partition editor before you start with existing HDD(s).
Step by step
1. Mount one or more HDDs to a frame and insert it in the TeraStation™.
2. Prepare the MicroSD and the USB adapter and insert the USB
adapter into a USB 2.0 port, connect power and network.
3. Move the boot switch to USB position.
4. Boot the TeraStation™.
Now the unit gives after some minutes a tone, the display
goes red and it says “push function button to start”.
5. Push the function button until beep sounds.
The display status color will be blue and sequence through these messages:
Recovery Preparing
System Recovering
FW/Updating
Recovery Finished, “Change Boot SW”
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
6. The TeraStation™ will shut down and the Power button will no
longer be lit green. The display and Info light stay on.
7. Remove the USB adapter, move the switch on the
back to HDD, press the power button
If you use just one drive you will have a brief warning for missing
HDDs and afterwards the TeraStation™ will operate normally.
If you use more than one drive: The first HDD is mounted and will work normally
and the other HDDs are mounted but not yet formatted. The display will therefore
turn red and the status LEDs of all unformatted drives will show red as well.
The warning, red display, and red LEDs will remain until you finish formatting all HDDs.
8. Now please install the NAS Navigator on your computer and click
‘Refresh’ to reveal your new TeraStation™ 4000. Right click on it and select
‘Settings’. A browser window will launch the admin interface. It’s also
possible to access the admin interface by entering the TS4000 series IP
address (shown on the TS’s display) directly into a browser window.
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
9. Format all unformatted HDDs via the admin interface. Once formatting
is completed the status in the admin page will change to ‘Formatted’
please wait to see this before continuing, depending on HDD
capacity this could take approximately 8 minutes per drive.
Produktspecifikationer
| Varumärke: | Buffalo |
| Kategori: | Server |
| Modell: | TS4400D |
Behöver du hjälp?
Om du behöver hjälp med Buffalo TS4400D ställ en fråga nedan och andra användare kommer att svara dig
Server Buffalo Manualer
7 Januari 2025
17 September 2024
16 September 2024
30 Augusti 2024
23 Augusti 2024
22 Augusti 2024
22 Augusti 2024
21 Augusti 2024
20 Augusti 2024
19 Augusti 2024
Server Manualer
- Advantech
- Rocstor
- Vimar
- IStarUSA
- Teradek
- TAIDEN
- Infortrend
- Iomega
- Sony
- GeoVision
- Sun
- Allnet
- Lindy
- Fantec
- Kramer
Nyaste Server Manualer
14 Juni 2025
13 Juni 2025
12 Juni 2025
8 Juni 2025
7 Juni 2025
7 Juni 2025
3 Juni 2025
30 Maj 2025
9 April 2025
3 April 2025