Bunn Trifecta Bruksanvisning
Bunn
kaffebryggare
Trifecta
Läs gratis den bruksanvisning för Bunn Trifecta (3 sidor) i kategorin kaffebryggare. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 5 recensioner. Har du en fråga om Bunn Trifecta eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
41831.0001A 03/10 ©2009 Bunn-O-Matic Corporation
Trifecta
Instructions for Installing
Control Board
KIT CONTENTS
1 40150.#### Control Board
6 02367.0000 Screws
6 29081.0001 spacers
1 41831.0001 Instructions
INSTRUCTIONS
Refer to illustrations.
1. Remove front access panel. FIG 1 & 2
INTRODUCTION
WARNING - The brewer must be disconnected from the power source until installation is completed. Allow
brewer to cool.
This instruction covers the installation of replacement Control Board.
Remove two screws.
Lower the panel as far
as it will go.
Push the top down to
clear the brew chamber
support arm, then pull
the top out fi rst.
FIG 1 FIG 2
CONTINUED
PROGRAM SWITCH
LOCK
SET
TANK THERMISTOR
BREW CHAMBER
INTERLOCK SWITCH
FIG 1
FIG 2
2. Disconnect harnesses from old board.
3. Remove six screws securing board to bracket.
4. Verify program switch on new board is in the “SET” position. Secure new board with six screws.
5. Reconnect harnesses. NOTE: Be sure each harness connector is properly aligned on each board connector.
See FIG 2 for the (2-pin) connectors.
6. Replace the front access panel. Connect to power source.
7. Place a large container (at least 40 ounces) under the brew chamber as shown in FIG 3. Start a brew cycle. The new
board will go through the tank fi ll procedure only on the initial brew cycle. If the tanks are already fi lled, you will
need the large container to capture the extra water. All brew cycles thereafter will return to normal amounts.
Installation is completed.
NOTE: New control board is set to factory defaults, refer to Programming manual and reprogram as needed.
Troubleshooting tips:
1. If board will not enter program modes, check position of program switch. FIG 1
2. If brewer malfunctions after board replacement, disconnect power and verify all connectors are properly aligned
on board. It may be possible to have a connector offset by one pin! Also verify the two (2 pin) connectors are
in the correct pin jacks. FIG 2.
FIG 3
Produktspecifikationer
| Varumärke: | Bunn |
| Kategori: | kaffebryggare |
| Modell: | Trifecta |
Behöver du hjälp?
Om du behöver hjälp med Bunn Trifecta ställ en fråga nedan och andra användare kommer att svara dig
kaffebryggare Bunn Manualer
12 Juni 2025
29 December 2024
29 December 2024
29 December 2024
24 September 2024
16 September 2024
15 September 2024
15 September 2024
12 September 2024
12 September 2024
kaffebryggare Manualer
- Bosch
- Rancilio
- Becken
- Smeg
- Bellarom
- Varo
- Dualit
- Daalderop
- Bialetti
- Grundig
- N8WERK
- Orava
- Ices
- Wittenborg
- Rosseto
Nyaste kaffebryggare Manualer
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025