Chamberlain 041-0202-000 Bruksanvisning
Chamberlain
Lättnad
041-0202-000
Läs gratis den bruksanvisning för Chamberlain 041-0202-000 (4 sidor) i kategorin Lättnad. Guiden har ansetts hjälpsam av 38 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 19.5 recensioner. Har du en fråga om Chamberlain 041-0202-000 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
Integrated LED Light Module
Replacement
Repair Parts 041-0200-000, 041-0201-000,
041-0202-000 and 041-0203-000
To prevent possible SERIOUS INJURY or DEATH:
• Disconnect ALL electric and battery power BEFORE performing ANY
service or maintenance.
To prevent damage to the receiver logic board, DO NOT touch printed
circuit board of replacement receiver/logic board during installation.
ALWAYS wear protective gloves and eye protection when changing the
battery or working around the battery compartment.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Introduction
Use this instruction to replace the integrated LED light module. The images
throughout this manual are for reference only and your product may look
different.
You will need:
• 1/4" magnetic nut driver
• Long-nosed pliers
• 5/16" long-shafted magnetic nut driver and socket
• Flathead screwdriver
Instructions
1. Disconnect the electrical and battery power (if applicable) to the garage
door opener. Remove the battery and place in a safe location.
2. Remove the control door panel from both ends of
the opener. (A)
a. Separate the hinges in
opposite directions.
b. Remove the panels from
the hinge setting and
place in a safe location.
3.
Disconnect the door control
wires from the RED and
WHITE terminals and the
safety reversal sensor wires
from the BLACK and WHITE
terminals. (B)
4. Remove the end panels from
both ends of the opener.
5. Remove the integrated LED
light module from the
opener. (C)
6. Disconnect the ORANGE and WHITE wire harness from plug to the
integrated LED light module and set aside cover / LED light module. (D)
7. Install the new integrated LED light module.
8. Connect the ORANGE and WHITE wire harness from the plug to the
Integrated LED Light Module. (D)
9. Align integrated LED light module to chassis screw holes.
10. Attach both end panels.
11. Reconnect the door control and safety reversal sensor wires. (B)
Door Control:
• WHITE wire into the WHITE terminal.
• WHITE/RED wire into the RED terminal.
Safety Reversal Sensors:
• WHITE wires into the WHITE terminal.
• WHITE/BLACK wires into the GRAY terminal.
12. Reattach the control door panels.
13. Reconnect power to the opener.
14. Test the Protector System.
RED
WHITE
WHITE
GREY
B
A
D
C
Integrated LED Light Module
Control Door Panel
End Panel
Produktspecifikationer
| Varumärke: | Chamberlain |
| Kategori: | Lättnad |
| Modell: | 041-0202-000 |
Behöver du hjälp?
Om du behöver hjälp med Chamberlain 041-0202-000 ställ en fråga nedan och andra användare kommer att svara dig
Lättnad Chamberlain Manualer
19 September 2024
13 September 2024
4 September 2024
25 Augusti 2024
13 Augusti 2024
12 Augusti 2024
11 Augusti 2024
3 Augusti 2024
31 Juli 2024
29 Juli 2024
Lättnad Manualer
- NZXT
- FeinTech
- Monster
- Amaran
- Brilliant
- LightZone
- Bright Spark
- Swisson
- Dorr
- Näve
- Stanley
- Gewiss
- Jung
- Denver
- Toolcraft
Nyaste Lättnad Manualer
9 April 2025
9 April 2025
9 April 2025
8 April 2025
8 April 2025
8 April 2025
7 April 2025
5 April 2025
5 April 2025
5 April 2025