Chief FDP4100B Bruksanvisning
Chief
Platt panelstöd
FDP4100B
Läs gratis den bruksanvisning för Chief FDP4100B (2 sidor) i kategorin Platt panelstöd. Guiden har ansetts hjälpsam av 5 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 3 recensioner. Har du en fråga om Chief FDP4100B eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
8803-000033 01/26/04
CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: chief@chiefmfg.com
INSTALLATION INSTRUCTIONS
FDP SERIES
SMALL FLAT PANEL DISPLAY
DUAL SCREEN POLE MOUNT
Exclusive Q2™ Mounting System
Prior to assembly, unpack carton completely and verify contents.
If you are missing any of the following components, please contact Customer Service at 1-800/582-6480.
(2) FDP Pole-Mounting Bracket Half (2) ¼” Flat Washer
(2) ¼-20 X 4.25” Hex Bolt (8) 10-24 X 1.00 Thread Forming Screw
(8) ½” X ½” Nylon Spacer
BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY
The FSP will fit on any 1/1/2” to 2” O.D. pipe including 1 ½”NPT.
Flat Panel Displays are Extremely Fragile.
If Monitor Uses a Screw Size Other Than M4 X 10mm (M4 X 20mm),
DO NOT USE M4 Screws Provided. Monitor Damage Could Occur.
Interface Bracket Installation:
1. See installation procedures accompanying your mounting bracket.
Optional Latching Flag Placement:
1. Remove Phillips head screw, Nylock nut and latching flag (see Figure 2).
2. Reposition latching flag and secure using Phillips head screw, Nylock nut.
Figure 1
Figure 2
CAUTION!
Remove screw
and nu
t
M
ove
l
atc
h
8803-000033 01/26/04
CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: chief@chiefmfg.com
Pole-Mounting Bracket Assembly and Installation:
1. Assemble two pole-mounting bracket halves as shown in Figure 3 and secure using two ¼-20 X 4.25”
hex bolts and two ¼” flat washers.
2. For vertical pole mounting, install the pole-mounting bracket on 1 ½” to 2” OD pipe/pole and secure
using 7/16” hex drives (see Figure 4).
3. For horizontal pole mounting; remove eight tilt adjustment screws, reposition the tilt bracket as
shown in Figure 5, and insert nylon spacers. Secure using 10-24 x 1.00 screws provided.
Mounting Display with Interface Bracket to Pole-Mounting Bracket:
1. Make sure both latching flags on pole-mounting bracket are in the unlocked position (see Figure 4).
2. Place your small flat panel displays; with interface brackets attached, onto the pole-mounting bracket,
making sure they are securely seated.
3. Engage pole-mounting bracket latching flags, locking small flat panel displays in place (see Figure 6).
4. Adjust tilt by loosening (slightly) tilt adjustment screws (see Figure 7) on each side of pole-mounting
bracket, adjust to desired angle, and tighten tilt adjustment screws.
Figure 3 Figure 4
Locked
Unlocked
Tighten to
secure to
p
ole
Tilt
Adjustment
Screws
Figure 6
10-24 x 1.00 screw
.500 O.D. x .500
long nylon spacer
Figure 7
¼-20 X 4.25” hex bolt
and ¼” washer
Figure 5
Produktspecifikationer
| Varumärke: | Chief |
| Kategori: | Platt panelstöd |
| Modell: | FDP4100B |
Behöver du hjälp?
Om du behöver hjälp med Chief FDP4100B ställ en fråga nedan och andra användare kommer att svara dig
Platt panelstöd Chief Manualer
3 April 2025
3 April 2025
3 April 2025
3 April 2025
9 Mars 2025
4 Mars 2025
4 Mars 2025
18 Februari 2025
6 Februari 2025
31 Januari 2025
Platt panelstöd Manualer
- Reflecta
- BenQ
- Newstar
- CTA Digital
- Multibrackets
- Marantz
- SmartMetals
- Unicol
- Kensington
- SunBriteTV
- One For All
- Iiyama
- LTN Technologies
- Bretford
- Kanto
Nyaste Platt panelstöd Manualer
8 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
2 April 2025
2 April 2025