Chief RPA204 Bruksanvisning
Sidor 1 Engels Platt panelstöd
Läs bruksanvisningen för Chief RPA204 gratis online eller ladda ner PDF:en. 24 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
INSTALLATION INSTRUCTIONS
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-
mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The
information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the
information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2007 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000271
9/10/07
SLB-204 and SLM-204 Interface Brackets
for Christie LX650, EIKI LC-X80, SANYO PLC-XP100L,
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1.Screw six thumb screws onto six 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2.Turn projector upside down on a flat surface.
3.Place the interface bracket onto the bottom of the projector lining up the four holes in the bracket with the four threaded inserts in the bottom
of the projector.
4..Using the four M6 X 12mm mounting screws and washers, start them into the mounting holes by hand and secure all four fasteners at
this time.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket(4) Washer, Flat, M6
(6) 10-24 Thumb Nuts **(4) SCREW, Pan head, M6 x 12mm
(1) All-Points Security Kit
**Only used when installing SLB Interface brackets.
SLB-204
SLM-204
Towards front ofTowards front of
Projector
Projector
Produktspecifikationer
| Varumärke: | Chief |
| Kategori: | Platt panelstöd |
| Modell: | RPA204 |
Behöver du hjälp?
Om du behöver hjälp med Chief RPA204 ställ en fråga nedan och andra användare kommer att svara dig
Platt panelstöd Chief Manualer
Chief iCLPFM2T03 Bruksanvisning Chief RPA261 Bruksanvisning Chief TPM2020 Bruksanvisning Chief iCXPTM3B03 Bruksanvisning Chief KWS220B Bruksanvisning Chief PL2A Bruksanvisning Chief CMA273 Bruksanvisning Chief SLB240 Bruksanvisning
Alla Chief Platt panelstöd manualer
Populära i Platt panelstöd
Platt panelstöd Manualer
Nyaste Platt panelstöd Manualer
Mount-It! MI-384 Bruksanvisning Proaim CT-VNGD-UC5 Bruksanvisning Premier Mounts 7170-0977 Bruksanvisning Mount-It! MI-766 Bruksanvisning Erard FLAK 800+ Bruksanvisning Ergotron Neo-Flex Widescreen Stand Bruksanvisning Ergotron WorkFit C-Mod Bruksanvisning Ergotron Neo-Flex Cantilever Bruksanvisning Ergotron 200 Series Combo Arm Bruksanvisning Ergotron Conversion Kit Bruksanvisning