Cotech 50076 Bruksanvisning

Läs gratis den bruksanvisning för Cotech 50076 (6 sidor) i kategorin Rörelsedetektor. Guiden har ansetts hjälpsam av 37 personer och har ett genomsnittsbetyg på 4.0 stjärnor baserat på 9 recensioner. Har du en fråga om Cotech 50076 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

GREAT BRITAIN • CUSTOMER SERVICEtel. 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk postal 10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ

Ver. 20160525

PIR Sensor

Art.no 36-6362 Model 50076

Please read theentire instruction manual before using theproduct and

then save it for future reference. Wereserve theright for any errors in

text or images and any necessary changes made to technicaldata.

Intheevent of technical problems or other queries, please contact our

Customer Services.

Things to consider:

• Other wireless equipment using thesame frequency band can

reduce thetransmissionrange.

• Therange of all wireless equipment depends on thetype of obstacles

located between thetransmitter and thereceiver (e.g. aconcrete wall

will interfere with thesignal more than aplasterboard wall).

If you experience problems, try thefollowing:

• Turn off any other existing wireless equipment to check whether

this is thecause of theproblem.

• Reposition thewireless equipment, shorten thedistance between

thetransmitter and thereceiver or reduce thenumber of obstacles

(walls, furniture,etc.) betweenthem.

Installation

Note: Thismotion sensor is designed for indoor useonly.

• Themotion sensor should be installed at least 1.2m above groundlevel.

• Do not install themotion sensor where it will be exposed to direct sunlight.

• Do not install themotion sensor in front of awindow, any kind of

fan or air conditioningunit.

• Do not install themotion sensor over or close to any type of heat source.

Operating instructions

Connection

Follow theprocedures below for pairing:

1. Make sure that thereceiver that you are going to use themotion

sensor with is ready to be paired (refer to theuser manual of

thereceiver).

2. Hold in [ Learn ] on themotion sensor for 1 second. Themotion

sensor will now pair with thereceiver.

Operating modes:

Themotion sensor has three operatingmodes:

• 24hr/10S: Whenaperson enters thedetection zone, themotion

sensor sends anon-signal to thereceiver. Whentheperson

leaves thedetection zone there is adelay of 10 seconds

before themotion sensor sends anoff-signal to thereceiver.

Iffurther motion is detected inside thedetection zone within

the10seconds, anew on-signal will be sent to thereceiver.

• 24hr/1M: Whenaperson enters thedetection zone, themotion

sensor sends anon-signal to thereceiver. Whentheperson leaves

thedetection zone there is adelay of 1 minute before themotion

sensor sends anoff-signal to thereceiver. Iffurther motion is

detected inside thedetection zone within the1 minute, anew

on-signal will be sent to thereceiver.

• 30S: Nightmode, on-signals are not sent during daylight.

Whenaperson enters thedetection zone in thedark, themotion

sensor sends anon-signal to thereceiver. Whentheperson

leaves thedetection zone there is adelay of 30 seconds

before themotion sensor sends anoff-signal to thereceiver.

Iffurther motion is detected inside thedetection zone within

the30seconds, anew on-signal will be sent to thereceiver.

Deleting the motion sensor from a receiver

It is not possible to delete (unpair) only themotion sensor from

areceiver. Inorder to delete themotion sensor from areceiver,

all thetransmitters paired with thereceiver must be deleted.

Readtheinstruction manual of thereceiver in question.

Care and maintenance

• Clean theproduct by wiping it with adampcloth. Useonly mild

cleaning agents, never solvents or corrosive chemicals.

• Remove thebattery and store themotion sensor out of reach of

children if it is not to be used for alongtime.

Changing the battery

1. Remove thecover of thebattery compartment from theback of

themotion sensor.

2. Insert anew battery (1×CR2450). Insert thebattery with the (+)

facing upwards.

3. Refit thebatterycover.

Troubleshooting guide

Themotion

sensor does

notwork.

• Check thebattery and replace it if necessary.

• Is themotion sensor paired with thereceiver as

describedabove? Trypairing themagain.

• Check that thedevice (e.g. light) which is

connected to thereceiver is switched on and

not faulty.

• Is themotion sensor too far from thereceiver?

• Is thesignal being blocked by furniture or

furnishings?

Responsible disposal

1. Remove theback of themotion

sensor.

2. Fix theback of themotion sensor in

thedesiredplace. Usetheincluded

screws and plugs or another

appropriate fastening method. Before

drilling mounting holes into thewall,

make sure that it is free from hidden

electrical wiring and waterpipes.

Remove theplastic tab to activate

thebattery. Oncethebattery Note:

has been activated it takes about

20seconds for themotion sensor to

fully activate.

This symbol indicates that this product should not be

disposed of with general householdwaste. Thisapplies

throughout theentire EU. Inorder to prevent any

harm to theenvironment or health hazards caused by

incorrect waste disposal, theproduct must be handed

in for recycling so that thematerial can be disposed

of in aresponsible manner. Whenrecycling your

product, take it to your local collection facility or contact

theplace of purchase. Theywill ensure that theproduct

is disposed of in anenvironmentally sound manner.

Specifications

Frequency 433.92 MHz

Range 25m

Battery 1×CR2450 (included)

PIR sensorrange ≤ 5m

Detectionangle 110°

Operating temperature 0–35 °C

Activation of night mode < 150 lux

Produktspecifikationer