Crunch GP-2000.4 Bruksanvisning

Crunch mottagare GP-2000.4

Läs gratis den bruksanvisning för Crunch GP-2000.4 (2 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 6 recensioner. Har du en fråga om Crunch GP-2000.4 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

Place terminal in a secure

position so that it won’t

accidentally contact the

negative battery post

Power / Ground

cable size

It is critical to use the proper

power and ground cable. Select

the size listed here for your

amplier model. Always use high

quality copper cable.

Cable size recommendations for

multi amp systems are available

on our website.

Properly route power,

speaker and RCA cables

through the vehicle.

Choose a mounting location

that will provide adequate air

ventilation. Mount the amplier to

a secure surface. Do not mount

the amplier upside down.

Using spade terminals, connect the

+12V to the power cable from the

battery, the REM to the source unit

turn-on wire and the GND to the

chassis ground..

Bare metal

Connect the RCA cables to

the INPUT connectors. The

OUTPUT can be used to

provide input for a second

amplier.

The HI INPUT is for use with

source units that do not offer

RCA outputs. Use the supplied

harness to connect to the

source unit’s speaker output.

Connect the power cable to the

positive battery terminal. The

power cable must be fused

within 18 inches of the battery

terminal.

Re-connect the negative

battery terminal making sure it

is securely tightened.

Using spade terminals, connect

the speaker cables to the speaker

output connectors. Follow the

diagram below that best ts your

speaker conguration.

The chassis ground connection

is critical to the performance

of the amplier. Choose a

location that is close to the

amplier. Completely scrape

away the paint and use a nut

and bolt if possible.

DO NOT USE AN EXISTING

FACTORY BOLT!

Disconnect

negative battery

terminal

Run Cables

Mount Amplier

Power

Connections

Signal Input

Low Level RCA

Signal Input

High Level

Positive Battery

Connection

Re-connect

Negative Battery

Terminal

Speaker

Connections

Chassis Ground

Be prepared to disarm your vehicle’s alarm and

to enter your radio / source unit code.

Stereo

Installation

Before you start

Monoblock

single woofer multiple woofersMonoblock

Bridged

CAUTION

Many new and factory radios require a reset code when

disconnected from battery power. This is an anti-theft

feature. Before unplugging power, you must determine if

your radio/source unit requires a reset code. Check the

operation manual for your vehicle or contact the dealer.

Turn the LEVEL control completely

counter-clockwise to minimum.

Level Control

6V 0.2V

INPUT

LEVEL

Right + (gray) 4CH REAR

Ch3 Right + (orange)

Ch3 Right - (pink)

Chassis Ground (black)

Ch4 Left + (blue)

Ch4 Left - (yellow)

Connect to factory speaker wire directly

Right - (brown)

Left - (green)

Left + (white)

Chassis ground (black)

4ga

Model Fuse Size Cable Size

GP-1000.2

GP-1500.2

GP-2000.2

GP-1000.4

GP-1500.4

GP-2000.4

GP-1500.1

GP-2500.1

GP-3500.1D

20A x 1

25A x 1

30A x 1

40A x 1

30A x 2

25A x 2

30A x 2

SPEAKER

LEFT

RIGHT

BRIDGED

OUTPUT

SPEAKER OUTPUT

SPEAKER

LEFT

RIGHT

BRIDGED

OUTPUT

Produktspecifikationer

Varumärke:	Crunch
Kategori:	mottagare
Modell:	GP-2000.4
Färg på produkten:	Blauw
Vikt:	500 g
Bredd:	109 mm
Djup:	96 mm
Höjd:	53 mm
Kraftkälla:	AC
Monteringsverktyg:	Ja
Inspänning:	110 - 220 V
Laser klass:	3R
Färg ljus:	Green, Red
Färg på laserstrålen:	Rood/groen
Lämplig för utomhusbruk:	Ja
Lämplig för inomhusbruk:	Ja
Fjärrkontroll ingår:	Ja
Typ produkt:	Discolaserprojector
Baldiameter:	- "
Laser strålar:	Ja
Laservåglängd (röd):	650 nm
Laservåglängd (grön):	532 nm
Laservågkraft (röd):	60 mW
Laservågkraft (grön):	20 mW