Ctek D250SE Bruksanvisning
Sidor 14 Engels Batteriladdare
Läs bruksanvisningen för Ctek D250SE gratis online eller ladda ner PDF:en. 59 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
EN•3
EN
SMARTPASS 120S
+OUT
+OUT
+IN
MANUAL
CONGRATULATIONS
on the purchase of your new CTEK charger providing professional battery care. This charger is
included in a series of professional chargers from CTEK SWEDEN AB and represents the latest
technology in battery charging. With the CTEK D250SE and SMARTPASS 120S you can be sure of
getting maximum performance from your dual battery system.
SAFETY
CALIFORNIA PROPOSITION 65
WARNING: This product contains chemical known to the state
of California to cause cancer or reproductive toxicity.
• The D250SE and SMARTPASS 120S have been developed for 12V lead-acid and LFP batteries.
Do not use the unit for any other type of battery.
• Wear protective goggles when connecting and disconnecting batteries.
• Battery acid is corrosive. Rinse with plenty of water immediately if you get acid on your skin or in
your eyes. Get medical assistance.
• Never use a charger with damaged electric cables. Check that the cables have not been dama-
ged by hot surfaces, sharp edges or in any other way.
• Explosive gases are generated while lead-acid batteries are being charged. Avoid any sparking
near the battery. Use in a well-ventilated location.
• Never place the charger above the battery, and avoid covering the charger during charging.
• Disconnect the battery terminal posts before installing.
• The D250SE and SMARTPASS 120S are not spark-free.
• The installation must include a fuse in accordance with the recommendations in the table
”CABLE AND FUSE RECOMMENDATIONS”.
Remember that all installations in boats must comply with ISO 10133!
1. The cabling from the batteries must have fuses near the batteries.
2. The batteries must be securely fastened in a ventilated space.
3. The cabling must be run through pipe ducting, separately from 230V/110V wiring (mains power),
or secured by clips at every 30 cm/1 ft.
4. Cabling in the engine compartment must be temperature rated at 70C/ 158F.
Temperature sensor 2 m/6 ft.
Connector plate
D250SE
SMARTPASS 120S
Temperature sensor 2 m/6 ft.
+IN Input Alternator+OUT Output Service battery
+IN Input Alternator+OUT Output Service battery
+IN Input Solar panelEarth Connection
+OUT Output Consumers
Smart alternator cable (red) 0.2 m/0.6 ft.
Smart alternator cable (red) 0.2 m/0.6 ft.
Negative cable connection
(black) 0.2 m/0.6 ft.
Battery select cable (black)
0.2 m/0.6 ft.
WARNING!
The D250SE and
SMARTPASS 120S are not
protected against reversed
polarity.
WARNING!
Check manual of Lithium-ion
battery before installing in
vehicle.
Produktspecifikationer
| Varumärke: | Ctek |
| Kategori: | Batteriladdare |
| Modell: | D250SE |
Behöver du hjälp?
Om du behöver hjälp med Ctek D250SE ställ en fråga nedan och andra användare kommer att svara dig
Batteriladdare Ctek Manualer
Ctek M15 Bruksanvisning Ctek MXT 14 Bruksanvisning Ctek CT5 Bruksanvisning Ctek CS ONE Bruksanvisning Ctek Smartpass 120T Bruksanvisning Ctek M300 Acculader Bruksanvisning Ctek MXS 15 Acculader Bruksanvisning Ctek LITHIUM XS Acculader Bruksanvisning
Alla Ctek Batteriladdare manualer
Populära i Batteriladdare
Ctek READY AUTOMOTIVE Bruksanvisning Ctek MXS 5.0 POLAR Acculader Bruksanvisning Ctek MXS 5.0 CHECK Acculader Bruksanvisning
Batteriladdare Manualer
Nyaste Batteriladdare Manualer
Hamilton Buhl LTT10 Bruksanvisning Orbis VIARIS COMBI Bruksanvisning Megger EVCA210 Bruksanvisning Voltcraft VC-CJS71 Bruksanvisning Voltcraft FSP-11312 Bruksanvisning Voltcraft Quick Start System 1000A Bruksanvisning Voltcraft SPS-1000 USB-V2 Bruksanvisning Voltcraft VC-CJS10 Bruksanvisning Voltcraft PS-10 Bruksanvisning Voltcraft VC-JS-800A-WP Bruksanvisning