Dell Alienware 13 Bruksanvisning
Läs gratis den bruksanvisning för Dell Alienware 13 (119 sidor) i kategorin Laptop. Guiden har ansetts hjälpsam av 5 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 3 recensioner. Har du en fråga om Dell Alienware 13 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/119
Alienware 13
Service Manual
Computer Model: Alienware 13
Regulatory Model: P56G
Regulatory Type: P56G001
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use
of your computer.
CAUTION: A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
Copyright 2014 Dell Inc. All rights reserved.© This product is protected by U.S. and
international copyright and intellectual property laws. Dell™ and the Dell logo are trademarks of
Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned
herein may be trademarks of their respective companies.
2015 - 01
Rev. A00
Contents
Before Working Inside Your Computer...................... 10
Before You Begin .............................................................................................. 10
Safety Instructions............................................................................................10
Recommended Tools......................................................................................... 12
After Working Inside Your Computer..........................13
Removing the Base Panel................................................. 14
Procedure...........................................................................................................14
Replacing the Base Panel..................................................17
Procedure........................................................................................................... 17
Removing the Memory Module(s)................................ 18
Prerequisites......................................................................................................18
Procedure...........................................................................................................18
Replacing the Memory Module(s)................................20
Procedure..........................................................................................................20
Post-requisites...................................................................................................21
Removing the Solid-State Drive................................... 22
Prerequisites.....................................................................................................22
Procedure.......................................................................................................... 22
Replacing the Solid-State Drive....................................26
Procedure..........................................................................................................26
Post-requisites..................................................................................................26
Removing the Hard Drive................................................. 27
Prerequisites..................................................................................................... 27
Procedure.......................................................................................................... 27
Replacing the Hard Drive.................................................. 31
Procedure...........................................................................................................31
Post-requisites.................................................................................................. 31
Removing the Palm Rest.................................................. 32
Prerequisites.....................................................................................................32
Procedure..........................................................................................................33
Replacing the Palm Rest.................................................. 39
Procedure..........................................................................................................39
Post-requisites..................................................................................................39
Removing the Touchpad..................................................40
Prerequisites.....................................................................................................40
Procedure..........................................................................................................40
Replacing the Touchpad...................................................42
Procedure.......................................................................................................... 42
Post-requisites..................................................................................................42
Removing the Keyboard.................................................. 43
Prerequisites.....................................................................................................43
Procedure..........................................................................................................44
Replacing the Keyboard................................................... 47
Procedure.......................................................................................................... 47
Post-requisites.................................................................................................. 47
Removing the Power-Button Board............................48
Prerequisites.....................................................................................................48
Procedure..........................................................................................................49
Replacing the Power-Button Board............................. 51
Procedure...........................................................................................................51
Post-requisites.................................................................................................. 51
Removing the Status-Light Board...............................52
Prerequisites.....................................................................................................52
Procedure..........................................................................................................53
Replacing the Status-Light Board............................... 55
Procedure..........................................................................................................55
Post-requisites..................................................................................................55
Removing the Display Assembly..................................56
Prerequisites.....................................................................................................56
Procedure..........................................................................................................56
Replacing the Display Assembly................................... 61
Procedure...........................................................................................................61
Post-requisites..................................................................................................62
Removing the Power-Adapter Port.............................63
Prerequisites.....................................................................................................63
Procedure..........................................................................................................63
Replacing the Power-Adapter Port............................. 67
Procedure.......................................................................................................... 67
Post-requisites.................................................................................................. 67
Removing the Heat-Sink Assembly............................ 68
Prerequisites.....................................................................................................68
Procedure..........................................................................................................69
Replacing the Heat-Sink Assembly.............................. 71
Procedure........................................................................................................... 71
Post-requisites...................................................................................................71
Removing the Wireless Card...........................................72
Prerequisites..................................................................................................... 72
Procedure.......................................................................................................... 72
Replacing the Wireless Card........................................... 74
Procedure.......................................................................................................... 74
Post-requisites.................................................................................................. 74
Removing the Coin-Cell Battery....................................75
Prerequisites..................................................................................................... 75
Procedure.......................................................................................................... 75
Replacing the Coin-Cell Battery.....................................77
Procedure...........................................................................................................77
Post-requisites.................................................................................................. 77
Removing the System Board..........................................78
Prerequisites..................................................................................................... 78
Procedure.......................................................................................................... 78
Replacing the System Board..........................................80
Procedure..........................................................................................................80
Post-requisites................................................................................................. 80
Removing the Battery........................................................ 81
Prerequisites......................................................................................................81
Procedure...........................................................................................................81
Replacing the Battery........................................................83
Procedure..........................................................................................................83
Post-requisites................................................................................................. 83
Removing the Speakers................................................... 84
Prerequisites.....................................................................................................84
Procedure..........................................................................................................84
Replacing the Speakers....................................................86
Procedure..........................................................................................................86
Post-requisites................................................................................................. 86
Removing the Computer Base....................................... 87
Prerequisites..................................................................................................... 87
Procedure.......................................................................................................... 87
Replacing the Computer Base....................................... 89
Procedure..........................................................................................................89
Post-requisites................................................................................................. 89
Removing the Display Bezel...........................................90
Prerequisites.....................................................................................................90
Procedure..........................................................................................................90
Replacing the Display Bezel............................................94
Procedure..........................................................................................................94
Post-requisites..................................................................................................94
Removing the Display Panel...........................................95
Prerequisites.....................................................................................................95
Procedure..........................................................................................................95
Replacing the Display Panel........................................... 98
Procedure..........................................................................................................98
Post-requisites................................................................................................. 98
Removing the Camera....................................................... 99
Prerequisites.....................................................................................................99
Procedure..........................................................................................................99
Replacing the Camera......................................................102
Procedure........................................................................................................ 102
Post-requisites................................................................................................102
Removing the Display Hinges......................................103
Prerequisites...................................................................................................103
Procedure........................................................................................................ 103
Replacing the Display Hinges...................................... 105
Procedure........................................................................................................ 105
Post-requisites................................................................................................105
Removing the Display Back-Cover.............................106
Prerequisites...................................................................................................106
Procedure.........................................................................................................107
Replacing the Display Back-Cover.............................. 110
Procedure.........................................................................................................110
Post-requisites.................................................................................................110
System Setup.........................................................................111
Overview ...........................................................................................................111
Entering System Setup .................................................................................... 111
System Setup Options................................................................................ 111
Boot Sequence................................................................................................. 115
Boot Options...............................................................................................116
Changing Boot Sequence for the Current Boot......................................... 116
Changing Boot Sequence for Future Boots................................................117
Flashing the BIOS................................................................ 118
Getting Help and Contacting Alienware.................. 119
Self-Help Resources......................................................................................... 119
Contacting Alienware.......................................................................................119
Before Working Inside Your
Computer
CAUTION: To avoid damaging the components and cards,
handle them by their edges and avoid touching pins and
contacts.
NOTE: The images in this document may differ from your computer
depending on the configuration you ordered.
Before You Begin
1 Save and close all open files and exit all open applications.
2 Shut down your computer.
– Windows 8.1: On the screen, click or tap the power icon Start →
Shut down.
– Windows 7: Click or tap .Start Shut down →
NOTE: If you are using a different operating system, see the
documentation of your operating system for shut-down instructions.
3 Disconnect your computer and all attached devices from their electrical
outlets.
4 Disconnect all cables such as telephone cables, network cables and so on,
from your computer.
5 Disconnect all attached devices and peripherals, such as keyboard, mouse,
monitor, and so on, from your computer.
6 Remove any media card and optical disc from your computer, if applicable.
Safety Instructions
Use the following safety guidelines to protect your computer from potential
damage and ensure your personal safety.
WARNING: Before working inside your computer, read the
safety information that shipped with your computer. For
more safety best practices, see the Regulatory Compliance
home page at dell.com/regulatory_compliance.
10
WARNING: Disconnect all power sources before opening the
computer cover or panels. After you finish working inside
the computer, replace all covers, panels, and screws before
connecting to the power source.
CAUTION: To avoid damaging the computer, make sure that
the work surface is flat and clean.
CAUTION: To avoid damaging the components and cards,
handle them by their edges and avoid touching pins and
contacts.
CAUTION: Only a certified service technician is authorized to
remove the computer cover and access any of the
components inside the computer. See the safety
instructions for complete information about safety
precautions, working inside your computer, and protecting
against electrostatic discharge.
CAUTION: Before touching anything inside your computer,
ground yourself by touching an unpainted metal surface,
such as the metal at the back of the computer. While you
work, periodically touch an unpainted metal surface to
dissipate static electricity, which could harm internal
components.
CAUTION: When you disconnect a cable, pull on its connector
or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs or thumb-screws that you
must disengage before disconnecting the cable. When
disconnecting cables, keep them evenly aligned to avoid
bending any connector pins. When connecting cables, make
sure that the ports and connectors are correctly oriented
and aligned.
CAUTION: To disconnect a network cable, first unplug the
cable from your computer and then unplug the cable from
the network device.
CAUTION: Press and eject any installed card from the media-
card reader.
11
Recommended Tools
The procedures in this document may require the following tools:
• Philips screwdriver
• Plastic scribe
12
After Working Inside Your
Computer
CAUTION: Leaving stray or loose screws inside your
computer may severely damage your computer.
1 Replace all screws and make sure that no stray screws remain inside your
computer.
2 Connect any external devices, peripherals, and cables you removed before
working on your computer.
3 Replace any media cards, discs, and any other part(s) that you removed
before working on your computer.
4 Connect your computer and all attached devices to their electrical outlets.
5 Turn on your computer.
13
Removing the Base Panel
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Close the display and turn the computer over.
2 Loosen the captive screws that secure the base panel to the computer
base.
14
3 Using a plastic scribe, gently release the tabs that secure the base panel to
the computer base.
1 computer base 2 captive screws (2)
3 base panel 4 plastic scribe
15
4 Disconnect the battery cable from the battery-cable connector.
1 battery cable 2 battery-cable connector
5 Turn the computer over.
6 Press and hold the power button for 5 seconds to ground the system
board.
16
Replacing the Base Panel
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Connect the battery cable to the battery-cable connector.
2 Align the tabs on the base panel with the slots on the computer base and
snap the base panel into place.
3 Tighten the captive screws that secure the base panel to the computer
base.
17
Removing the Memory
Module(s)
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Prerequisites
Remove the .base panel
Procedure
1 Using your fingertips, carefully spread apart the securing clips on each end
of the memory-module slot until the memory module pops up.
18
2 Slide and remove the memory module from the memory-module slot.
1 securing clips (2) 2 memory modules (2)
3 memory-module slot
19
Replacing the Memory
Module(s)
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Align the notch on the memory module with the tab on the memory-
module slot.
20
2 Slide the memory module firmly into the slot at an angle and press the
memory module down until it clicks into place.
NOTE: If you do not hear the click, remove the memory module and
reinstall it.
1 securing clips (2) 2 notch
3 tab 4 memory module
5 memory-module slot
Post-requisites
Replace the .base panel
21
Removing the Solid-State
Drive
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
CAUTION: Solid-state drives are fragile. Exercise care when
handling the hard drive.
CAUTION: To avoid data loss, do not remove the solid-state
drive while the computer is in sleep or on state.
Prerequisites
Remove the .base panel
Procedure
NOTE: Your computer can accommodate either one 2.5-inch hard drive or
two solid-state drives.
1 Remove the screws that secure the solid-state drive bracket to the solid-
state drive assembly.
22
4 Remove the screws that secure the solid-state drive assembly to the
computer base.
1 pull tab 2 solid-state drive cable
3 solid-state drive assembly 4 screws (2)
5 Lift the solid-state drive assembly off the computer base.
6 Remove the screw that secures the solid-state drive to the solid-state
drive assembly.
24
7 Slide and lift the solid-state drive off the solid-state drive assembly.
1 solid-state drive slots (2) 2 solid-state drive
3 solid-state drive assembly 4 screw
25
Removing the Hard Drive
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when
handling the hard drive.
CAUTION: To avoid data loss, do not remove the hard drive
while the computer is in sleep or on state.
Prerequisites
Remove the .base panel
Procedure
NOTE: Your computer can accommodate either one 2.5-inch hard drive or
two solid-state drives.
1 Remove the screws that secure the hard-drive assembly to the computer
base.
2 Using the pull tab, disconnect the hard-drive cable from the system board.
27
3 Lift the hard-drive assembly off the computer base.
1 pull tab 2 hard-drive cable
3 hard-drive assembly 4 screws (4)
4 Remove the screws that secure the hard-drive bracket to the hard drive.
28
5 Lift the hard drive off the hard-drive bracket.
1 hard-drive bracket 2 screws (4)
3 hard drive
29
6 Disconnect the interposer from the hard drive.
1 interposer 2 hard drive
30
Replacing the Hard Drive
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when
handling the hard drive.
Procedure
1 Connect the interposer to the hard drive.
2 Align the screw holes on the hard-drive bracket with the screw holes on
the hard-drive assembly.
3 Replace the screws that secure the hard-drive bracket to the hard-drive
assembly.
4 Align the screw holes on the hard-drive assembly with the screw holes on
the computer base.
5 Replace the screws that secure the hard-drive assembly to the computer
base.
6 Connect the hard-drive cable to the system board.
Post-requisites
Replace the .base panel
31
Removing the Palm Rest
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Prerequisites
1 Remove the .base panel
2 Follow the procedure from step 1 to step 5 in “Removing the solid-state
drive”.
32
Procedure
1 Lift the latches and disconnect the keyboard and keyboard-backlight
cables from the system board.
1 keyboard-backlight cable 2 keyboard cable
33
2 Remove the screws that secure the palm-rest assembly to the computer
base.
1 screws (14) 2 computer base
34
3 Lift the computer base slightly and push the release tabs on the palm-rest
assembly until it pops out.
1 release tabs
4 Turn the computer over and open the display as far as possible.
5 Using a plastic scribe, pry up along the edges of the palm-rest assembly.
35
6 Gently lift the palm-rest assembly and turn it over.
1 palm-rest assembly
7 Lift the connector latch and disconnect the power-button board cable from
the system board.
36
8 Lift the palm-rest assembly off the computer base.
1 palm-rest assembly 2 connector latch
3 power-button board cable
9 Remove the .keyboard
10 Remove the .power-button board
11 Remove the .status-light board
37
Replacing the Palm Rest
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Replace the .touchpad
2 Replace the .status-light board
3 Replace the .power-button board
4 Replace the .keyboard
5 Connect the power-button board cable to the system board.
6 Align the palm-rest assembly on the computer base and snap it into place.
7 Close the display and turn the computer over.
8 Replace the screws that secure the palm-rest assembly to the computer
base.
9 Connect the keyboard cable and the keyboard-backlight cable to the
system board.
Post-requisites
1 Follow the procedure from step 3 to step 7 in “Replacing the solid-state
drive” .
2 Replace the .base panel
39
Removing the Touchpad
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Prerequisites
1 Remove the .base panel
2 Follow the procedure from step 1 to step 5 in “Removing the solid-state
drive”.
3 Follow the procedure from step 1 to step 8 in “Removing the ”.palm rest
Procedure
1 Lift the connector latch and disconnect the touchpad cable from the
touchpad.
2 Remove the screws that secure the touchpad to the palm-rest assembly.
40
3 Lift the touchpad off the palm-rest assembly.
1 screws (4) 2 touchpad cable
3 touchpad
41
Replacing the Touchpad
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Align the screw holes on the touchpad with the screw holes on the palm-
rest assembly.
2 Replace the screws that secure the touchpad to the palm-rest assembly.
3 Slide the touchpad cable into the touchpad connector and press down the
latch to secure the cable.
Post-requisites
1 Follow the procedure from step 5 to step 9 in “Replacing the ”.palm rest
2 Follow the procedure from step 3 to step 7 in “Replacing the solid-state
drive” .
3 Replace the .base panel
42
Removing the Keyboard
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Prerequisites
1 Remove the .base panel
2 Follow the procedure from step 1 to step 5 in “Removing the solid-state
drive”.
3 Follow the procedure from step 1 to step 8 in “Removing the ”.palm rest
43
Procedure
1 Lift the connector latches and disconnect the touchpad cable and the
status-light cable from the power-button board.
1 connector latches (2) 2 touchpad cable
3 status-light cable
2 Peel the touchpad cable and status-light cable off the keyboard bracket.
44
3 Remove the screws that secure the keyboard bracket to the palm-rest
assembly.
1 keyboard bracket 2 screws (12)
4 Lift the keyboard bracket off the palm-rest assembly.
5 Remove the screws that secure the keyboard to the palm-rest assembly.
45
6 Slide and lift the keyboard, along with the cables, off the palm-rest
assembly.
1 tabs (3) 2 keyboard
3 screws (2)
46
Replacing the Keyboard
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Align the screw holes on the keyboard with the screw holes on the palm-
rest assembly.
2 Replace the screws that secure the keyboard to the palm-rest assembly.
3 Align the screw holes on the keyboard bracket with the screw holes on the
palm-rest assembly.
4 Replace the screws that secure the keyboard bracket to the palm-rest
assembly.
5 Adhere the touchpad cable and status-light cable to the keyboard bracket.
6 Slide the touchpad cable and the status-light cable into their respective
connectors on the power-button board and press down the latches to
secure the cables.
Post-requisites
1 Follow the procedure from step 5 to step 9 in “Replacing the ”.palm rest
2 Follow the procedure from step 3 to step 7 in “Replacing the solid-state
drive” .
3 Replace the .base panel
47
Removing the Power-Button
Board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Prerequisites
1 Remove the .base panel
2 Follow the procedure from step 1 to step 5 in “Removing the solid-state
drive”.
3 Follow the procedure from step 1 to step 8 in “Removing the ”.palm rest
4 Follow the procedure from step 1 to step 4 in “Removing the ”.keyboard
48
Procedure
1 Lift the connector latch and disconnect the power-button board cable from
the power-button board.
1 connector latch 2 power-button board cable
49
2 Remove the screw that secures the power-button board to the palm-rest
assembly.
1 power-button board 2 screw
3 Lift the power-button board off the palm-rest assembly.
50
Replacing the Power-Button
Board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Slide the power-button board cable into the power-button board connector
and press down the latch to secure the cable.
2 Align the screw hole on the power-button board with the screw hole on the
palm-rest assembly.
3 Replace the screw that secures the power-button board to the palm-rest
assembly.
Post-requisites
1 Follow the procedure from step 3 to step 6 in “Replacing the ”.keyboard
2 Follow the procedure from step 5 to step 9 in “Replacing the ”.palm rest
3 Follow the procedure from step 3 to step 7 in “Replacing the solid-state
drive” .
4 Replace the .base panel
51
Removing the Status-Light
Board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Prerequisites
1 Remove the .base panel
2 Follow the procedure from step 1 to step 5 in “Removing the solid-state
drive”.
3 Follow the procedure from step 1 to step 8 in “Removing the ”.palm rest
4 Follow the procedure from step 1 to step 4 in “Removing the ”.keyboard
52
Procedure
1 Lift the connector latch and disconnect the status-light board cable from
the status-light board.
1 status-light board 2 status-light board cable
53
2 Remove the screw that secures the status-light board to the palm-rest
assembly.
1 screw 2 status-light board
3 Lift the status-light board off the palm-rest assembly.
54
Replacing the Status-Light
Board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Slide the status-light board cable into the status-light board connector
and press down the latch to secure the cable.
2 Align the screw hole on the status-light board with the screw hole on the
palm-rest assembly.
3 Replace the screw that secures the status-light board to the palm-rest
assembly.
Post-requisites
1 Follow the procedure from step 3 to step 4 in “Replacing the ”.keyboard
2 Follow the procedure from step 5 to step 9 in “Replacing the ”.palm rest
3 Follow the procedure from step 3 to step 7 in “Replacing the solid-state
drive” .
4 Replace the .base panel
55
3 Slide and lift the hinge caps off the display hinges.
1 screws (2) 2 hinge caps (2)
4 Close the display and turn the computer over.
5 Peel off the adhesive tape from the wireless card.
6 Remove the screw that secures the wireless-card bracket to the wireless
card.
57
7 Disconnect the antenna cables from the wireless card.
1 adhesive tape 2 screw
3 wireless-card bracket 4 antenna cables
8 Turn the computer over and open the display.
9 Peel off the adhesive tapes that secure the antenna cables to the system
board.
NOTE: Make note of the cable routing before removing any cable from
its routing guide.
10 Remove the antenna cables from the routing guides on the display hinges.
11 Lift the connector latch and disconnect the display cable from the system
board.
12 Remove the display cable from the routing guides on the display hinges.
58
14 Remove the screws that secure the display assembly to the computer
base.
1 display assembly 2 screws (4)
3 display hinges (2)
15 Lift the display assembly off the computer base.
60
12 Turn the computer over and open the display.
13 Align the screw holes on the hinge caps with the screw holes on the
display hinges.
14 Replace the screws that secure the hinge caps to the display hinges.
Post-requisites
1 Follow the procedure from step 5 to step 9 in “Replacing the ”.palm rest
2 Follow the procedure from step 3 to step 7 in “Replacing the solid-state
drive” .
3 Replace the .base panel
62
Removing the Power-
Adapter Port
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Prerequisites
1 Remove the .base panel
2 Follow the procedure from step 1 to step 5 in “Removing the solid-state
drive”.
3 Follow the procedure from step 1 to step 8 in “Removing the ”.palm rest
4 Remove the .display assembly
Procedure
1 Remove the screw that secures the power-adapter port bracket to the
power-adapter port.
2 Lift the power-adapter port bracket off the power-adapter port.
3 Release the power-adapter port from the computer base.
63
4 Disconnect the speaker cable from the system board.
1 power-adapter port bracket 2 screws (2)
3 speaker cable
64
5 Remove the screws that secure the system board to the computer base.
1 system board 2 screws (3)
6 Slide and lift the system-board assembly.
7 Turn the system-board assembly over.
65
8 Disconnect the power-adapter port cable and remove the power-adapter
port from the system board.
1 power-adapter port cable 2 system-board connector
66
Replacing the Power-
Adapter Port
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Procedure
1 Connect the power-adapter port cable to the system board.
2 Turn the system board over.
3 Replace the screws that secure the system board to the computer base.
4 Connect the speaker cable to the connector on the system board.
5 Align the power-adapter port to the computer base.
6 Align the screw hole on the power-adapter port bracket with the screw
hole on the power-adapter port.
7 Replace the screw that secures the power-adapter port bracket to the
power-adapter port.
Post-requisites
1 Replace the .display assembly
2 Follow the procedure from step 5 to step 9 in “Replacing the ”.palm rest
3 Follow the procedure from step 3 to step 7 in “Replacing the solid-state
drive” .
4 Replace the .base panel
67
Removing the Heat-Sink
Assembly
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
WARNING: The heat sink may become hot during normal
operation. Allow sufficient time for the heat sink to cool
before you touch it.
CAUTION: For maximum cooling of the processor, do not
touch the heat transfer areas on the heat sink. The oils in
your skin can reduce the heat transfer capability of the
thermal grease.
Prerequisites
1 Remove the .base panel
2 Follow the procedure from step 1 to step 5 in “Removing the solid-state
drive”.
3 Follow the procedure from step 1 to step 8 in “Removing the ”.palm rest
4 Remove the .display assembly
5 Follow the procedure from step 1 to step 5 in “Removing the power-adapter
port”.
68
Procedure
1 Disconnect the fan cables from the connectors on the system board.
1 connectors (2) 2 fan cables(2)
2 Turn the system board over.
69
3 Remove the screws that secure the heat-sink assembly to the system
board.
1 heat-sink assembly 2 screws (7)
4 Lift the heat-sink assembly off the system board.
70
Replacing the Heat-Sink
Assembly
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
CAUTION: Incorrect alignment of the heat sink can cause
damage to the system board and processor.
Procedure
1 Align the screw holes on the heat-sink assembly with the screw holes on
the system board.
2 Replace the screws that secure the heat-sink assembly to the system
board.
3 Turn the system board over.
4 Connect the fan cables to the connectors on the system board.
Post-requisites
1 Follow the procedure from step 2 to step 7 in “Replacing the power-adapter
port”.
2 Replace the .display assembly
3 Follow the procedure from step 5 to step 9 in “Replacing the ”.palm rest
4 Follow the procedure from step 3 to step 7 in “Replacing the solid-state
drive” .
5 Replace the .base panel
71
Removing the Wireless Card
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before Working Inside Your Computer.
After working inside your computer, follow the instructions
in . For more safety best After Working Inside Your Computer
practices, see the Regulatory Compliance home page at
dell.com/regulatory_compliance.
Prerequisites
1 Remove the .base panel
2 Follow the procedure from step 1 to step 5 in “Removing the solid-state
drive”.
3 Follow the procedure from step 1 to step 8 in “Removing the ”.palm rest
4 Remove the .display assembly
5 Follow the procedure from step 1 to step 5 in “Removing the power-adapter
port”.
Procedure
Slide the wireless card from the wireless-card slot on the system board.
72
Produktspecifikationer
| Varumärke: | Dell |
| Kategori: | Laptop |
| Modell: | Alienware 13 |
Behöver du hjälp?
Om du behöver hjälp med Dell Alienware 13 ställ en fråga nedan och andra användare kommer att svara dig
Laptop Dell Manualer
2 April 2025
13 Mars 2025
26 Februari 2025
23 Februari 2025
28 Januari 2025
7 Januari 2025
31 December 2025
12 December 2024
12 December 2024
12 December 2024
Laptop Manualer
- Schenker
- Huawei
- Lexibook
- SPC
- Mpman
- Odys
- MSI
- Ergotron
- SIIG
- Ricatech
- Nec
- Tripp Lite
- Inovia
- General Dynamics Itronix
- Schneider
Nyaste Laptop Manualer
5 April 2025
3 April 2025
28 Mars 2025
28 Mars 2025
26 Mars 2025
7 Mars 2025
5 Mars 2025
1 Mars 2025
23 Februari 2025
23 Februari 2025