Dell W-AP124/125 Bruksanvisning
Dell
Inte kategoriserad
W-AP124/125
Läs gratis den bruksanvisning för Dell W-AP124/125 (8 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 8 personer och har ett genomsnittsbetyg på 3.5 stjärnor baserat på 4.5 recensioner. Har du en fråga om Dell W-AP124/125 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/8
AP-120-MNT-CV Access Point Enclosure
Installation Guide
0510596-02 | July 2010 1
Introduction
The AP-120-MNT-CV access point (AP) enclosure is designed to provide some protection and limited
access to an AP-121 or AP-125. The AP-120-MNT-CV can be installed directly over a standard junction
box or on the ceiling, using ceiling tile rails.
To install the AP-120-MNT-CV on a wall, proceed to "Installing the AP-120-MNT-CV on a Wall" on page2.
To install the AP-120-MNT-CV on a ceiling, proceed to "Installing the AP-120-MNT-CV on a Ceiling" on
page5.
The AP-120-MNT-CV kit includes the following:
z1x Plastic base, which attaches to the AP
z1x Plastic cover, which hides the AP’s ports
z1x Plastic outlet-mounting plate
z1x 9/16" ceiling tile adapter
z1x 15/16" ceiling tile adapter
Additional Tools
zA screwdriver that matches the screws in the cover plate over the installed junction box
z(Optional) flat-head screwdriver or similar tool to punch out antenna access cutouts
Cover
Base
Mounting
Plate
Parts not to scale
9/16" Rail Adapter
15/16" Rail Adapter
2 AP-120-MNT-CV Access Point Enclosure | Installation Guide
Installing the AP-120-MNT-CV on a Wall
1. Attach the base plate as follows:
a. Remove the cover plate from an installed junction box (Figure 1). Save the screws.
Figure 1 Removing the installed cover plate
b. Identify the Ethernet cable or cables that will be connected to the AP-121 or AP-125. The
Ethernet cable must have a male RJ-45 connector.
c. Attach the mounting plate to the junction box using the screws from the removed cover plate
(Figure 2).
Figure 2 Installing the mounting plate
AP-120-MNT-CV Access Point Enclosure | Installation Guide 3
2. With the hook on the base facing away from the wall, pull the ethernet cables through the holes on
either side of the base. Hold the cable down and out of the way.
3. Place the AP into the base ( ). Place the top AP into the hookFigure 3 s on the base and align the back
of the AP with the large opening in the base.
Figure 3 AP installed in the base
4. Connect the ethernet cable or cables to the AP (Figure 4). Ensure that the cables do not obstruct any
of the connection points between the base and the cover.
Figure 4 Cable path
Produktspecifikationer
| Varumärke: | Dell |
| Kategori: | Inte kategoriserad |
| Modell: | W-AP124/125 |
Behöver du hjälp?
Om du behöver hjälp med Dell W-AP124/125 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Dell Manualer
12 December 2024
12 December 2024
23 September 2024
21 September 2024
14 September 2024
14 September 2024
14 September 2024
14 September 2024
13 September 2024
13 September 2024
Inte kategoriserad Manualer
- Medeli
- Huion
- Celexon
- Ingenuity
- FoxFury
- Ultimate Support
- Moultrie
- Smart365
- Toa
- Nxg
- Kramer
- Saturn
- Paasche
- Ankarsrum
- Trijicon
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025