Denver SC-17 Bruksanvisning
Läs gratis den bruksanvisning för Denver SC-17 (62 sidor) i kategorin Babyvakt. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 2 recensioner. Har du en fråga om Denver SC-17 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/62
SC-17
User manual
ENG 1
ENGLISH
This chapter provides instructions to install the video baby monitor.
At the first use, please recharge the battery inside the parent unit by using the
power adapter.
The baby unit has a lens cover. Please remove this lid before you start to use the
video baby monitor.
Installation
ALERT
Before placing the camera in a denitive way (baby unit) it is advisable to check the proper
functioning of equipment and proper radio communication between parent unit and baby unit.
1.Connect the 5VDC – 1.000 mA power adapter to parent unit.
The power socket (DC5V ) is in the left side on parent
unit.
Parent Unit – Power adapter
The parent unit has a rechargeable battery, so
when it is charged enough, you can use the device
without the power adapter. For more details please
refer to the parent unit chapter.
NOTE
2.Press the power button , the green power LED available
in the left side will light ON. The display will show as picture
below:
Parent Unit – Power ONParent Unit – LCD panel
3.Connect the 5VDC – 1.000 mA power adapter to Baby Unit
(wireless camera). The power socket (DC5V ) is in
the back side.
The wireless camera can use 3 x AAA batteries
(not included). For more details please refer to
Baby Unit chapter
Baby Unit – Power adapter
4.Press and hold the POWER ON/OFF button for 5-6 seconds
until the LED will flashing in red colour. This means that the
pairing phase is started.
Baby Unit – Power ON
5.With a thin object, such as a paper clip, press the RESET
button on the back side of the parent unit, the display should
show the images and you can hear the sound picked up by the
microphone inside the wireless camera.
Now you can turn o the camera and place it in
the nal place. For next use is no longer necessary
to repeat the pairing phase.
Parent Unit - Pairing
NOTE
ENG 2
ENGLISH
ENG 3
ENGLISH
Description
Parent Unit – Volume
Parent Unit – Radio signal strength
Parent Unit – Main menu
The pairing phase must be completed within 30 seconds. If you are unable to
complete its on time, wait until the red LED on the camera stays light ON, then
turn o the camera and try again. Once successfully completed there is no need
to repeat the pairing phase.
This chapter provides a description of parent unit and baby unit.
Parent Unit - Description
1.Power button (ON/OFF)
2.LCD Panel
3.Channel radio (1-2-3-4)
4.TALK button
5. and OK buttons
6.Speaker
7.RESET button
8.Le side: power connector and LED
9.Right side: AV OUT connector
10.Clip
11.Radio signal strength icon
12.Channel icon
13.Battery charge icon
Parent Unit – Talk and Listen function
This appliance has a dual connection between parent unit and baby unit (2 ways). This means
that you can speak with your baby by talking in the microphone inside the parent unit and your
voice will be heard by the baby through the speaker inside the camera, so you can calm him
without moving.
To talk with your baby please follow these steps:
1.Please check if the wireless camera is active then power ON the parent unit.
2.Press and hold the TALK button then start to speak near the parent unit.
3.Release the TALK button to listen your baby.
To set the volume in the parent unit, please follow these steps:
1.Power ON the parent unit.
2.Press or buttons and select your desired volume level. It is possible to set a volume level
from 0 to 9. The selected value will be stored in the parent unit.
2
1
3
4
5
10
9
6
7
8
11
12
13
LCD Panel
If you select “0” (zero) the audio in the parent unit will be disabled.
If the parent unit is near the baby unit you could hear a noise as “whistle”. To
x this inconvenience please place the wireless camera far from parent unit or
decrease the volume.
The LCD panel shows the radio signal strength icon.
Parent Unit – Battery
The parent unit has inside a rechargeable battery. At the rst use it is recommended to fully
charge the battery by connecting the power adapter to parent unit and t it in a compatible
power outlet.
Full charge. The battery life is approximately 5 hours.
To enter in the main menu, power ON the parent unit and press the OK button.
Listed below the options available:
1.ZOOM IN/OUT
2.BABY UNIT VOLUME
3.EFFECT SET
4.SETUP
5.TV OUT
Press or buttons to select an option and press OK button to conrm the selection.
Good signal. This is the optimal condition to use the appliance.
Low signal. There is communication between parent unit and baby unit, but you
risk to loose the signal. It is recommended to change the position of baby unit or
decrease the distance between parent unit and wireless camera.
No signal. There is not any communication between parent and baby unit.
NOTE
NOTE
Completely discharged battery. Charge the battery by connecting the parent unit
to the power adapter.
Low charge. The battery is very low and therefore will need to connect the power
adapter soon.
Produktspecifikationer
| Varumärke: | Denver |
| Kategori: | Babyvakt |
| Modell: | SC-17 |
Behöver du hjälp?
Om du behöver hjälp med Denver SC-17 ställ en fråga nedan och andra användare kommer att svara dig
Babyvakt Denver Manualer
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
10 Februari 2025
26 September 2024
25 September 2024
Babyvakt Manualer
- Swissvoice
- Modern-Electronics
- Babymoov
- Chicco
- Medisana
- Tristar
- Sanitas
- Hartig And Helling
- Trebs
- Lionelo
- Ariete
- Basetech
- Concept
- Mobi
- Goclever
Nyaste Babyvakt Manualer
3 Augusti 2025
1 Augusti 2025
1 Augusti 2025
31 Juli 2025
30 Juli 2025
28 Juli 2025
26 Juli 2025
26 Juli 2025
25 Juli 2025
19 Juli 2025