DeWalt DC520K Bruksanvisning

DeWalt Skruvmaskin DC520K

Läs gratis den bruksanvisning för DeWalt DC520K (7 sidor) i kategorin Skruvmaskin. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 6.5 recensioner. Har du en fråga om DeWalt DC520K eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/7

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVOADVERTENCIA:

ANTES DE USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black

color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box

configuration; and the array of lozenge-shaped humps on the surface of the tool.

DW979 12 Volt Cordless Drywall/Deck Screwdriver

DC520 18 Volt Cordless Drywall/Deck Screwdriver

DW979 Tournevis sans fil de 12 volts pour cloisons sèches/terrasses

DC520 Tournevis sans fil de 18 volts pour cloisons sèches/terrasses

DW979 Atornillador inalámbrico de 12 voltios para muro seco y placa de tablero

DW520 Atornillador inalámbrico de 18 voltios para muro seco y placa de tablero

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Rules – For All Battery Operated Tools

WARNING! Read and understand all instructions. Failure to follow all

instructions listed below may result in electric shock, fire and/or serious per-

sonal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

•Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes.

•Keep bystanders, children, and visitors away while operating a power tool. Distractions

can cause you to lose control.

ELECTRICAL SAFETY

•Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat,

oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords

may create a fire.

•A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery. A charger that may be suitable

for one type of battery may create a risk of fire when used with another battery.

•Use battery operated tool only with the specifically designated battery pack. Use of any

other batteries may create a risk of fire.

PERSONAL SAFETY

•Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medica-

tion. A moment of inattention while operating power tools may result in serious personal

injury.

•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair

can be caught in moving parts. Air vents often cover moving parts and should also be

avoided.

•Avoid accidental starting. Be sure switch is in the locked or off position before

inserting battery pack. Carrying tools with your finger on the switch or inserting the

battery pack into a tool with the switch on invites accidents.

•Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

•Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

•Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to a loss

of control.

•Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

•Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with

the switch is dangerous and must be repaired.

•Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tool. Such

preventative safety measures reduce the risk of starting the tool accidentally.

•Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

•When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another. Shorting the battery terminals together may

cause sparks, burns, or a fire.

•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

•Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

•Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may create a risk of injury when used on

another tool.

SERVICE

•Tool service must be performed only by qualified repair personnel. Service or mainte-

nance performed by unqualified personnel may result in a risk of injury.

•When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of shock or injury.

Additional Specific Safety Rules

•Hold tool by insulated gripping surfaces when performing an operation where the tool

may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts

of the tool “live” and shock the operator.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may pro-

mote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions and

duration of use, noise from this product may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable surface where it will not

cause a tripping or falling hazard. Some tools with large battery packs will stand upright on

the battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V ..................volts A ....................amperes

Hz ................hertz W ....................watts

min ..............minutes ..................alternating current

............direct current no....................no load speed

................Class I Construction ....................earthing terminal

....................(grounded) ....................safety alert symbol

..................Class II Construction …/min ............revolutions or reciprocation

.................... ........................(double insulated) per minute

BPM ............beats per minute

Important Safety Instructions for Battery Packs

Your tool uses a D WALT battery pack. When ordering replacement battery packs, be sure toE

include catalog number and voltage: Extended Run-Time battery packs deliver 25% more run-

time than standard battery packs. Consult the chart at the end of this manual for compatibility of

chargers and battery packs.

NOTE: Your tool will accept either standard or Extended Run Time battery packs. However, be

sure to select proper voltage. Batteries slowly lose their charge when they are not on the charg-

er, the best place to keep your battery is on the charger at all times.

The battery pack is not fully charged out of the carton. Before using the battery pack and charg-

er, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

•Do not incinerate the battery pack even if it is severely damaged or is completely worn

out. The battery pack can explode in a fire.

•A small leakage of liquid from the battery pack cells may occur under extreme usage

or temperature conditions. This does not indicate a failure. However, if the outer seal is bro-

ken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10 min-

utes and seek immediate medical attention. ( The liquid is 25-35% solutionMedical note:

of potassium hydroxide.)

• Charge the battery packs only in DEWALT chargers.

•DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature may

reach or exceed 105°F (40 ºC) (such as outside sheds or metal buildings in summer).

DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If

battery pack case is cracked or damaged, do not insert into charger. Electric shock or electrocu-

tion may result. Damaged battery packs should be returned to service center for recycling.

NOTE: Battery storage and carrying caps are providedfor use whenever the battery

is out of the tool or charger. Remove cap before placing battery in charger or tool.

WARNING: Fire hazard. Do not store or carry battery so that metal objects

can contact exposed battery terminals. For example, do not place battery in

aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails,

screws, keys, etc. without battery cap. Transporting batteries can possibly cause

fires if the battery terminals inadvertently come in contact with conductive materials such

as keys, coins, hand tools and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes

(i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short

circuits. So when transporting individual batteries, make sure that the battery terminals are pro-

tected and well insulated from materials that could contact them and cause a short circuit.

CAUTION: Battery pack must be securely attached to tool. If battery pack is detached, per-

sonal injury may result.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel

cadmium and nickel metal hydride batteries (or battery packs) indicate that the

costs to recycle these batteries (or battery packs) at the end of their useful life have

already been paid by DEWALT. In some areas, it is illegal to place spent nickel cad-

mium and nickel metal hydride batteries in the trash or municipal solid waste

stream and the RBRC program provides an environmentally conscious alternative.

RBRC™ in cooperation with DEWALT and other battery users, has established programs in the

United States and Canada to facilitate the collection of spent nickel cadmium and nickel metal

hydride batteries. Help protect our environment and conserve natural resources by returning the

spent nickel cadmium and nickel metal hydride batteries to an authorized DEWALT service cen-

ter or to your local retailer for recycling. You may also contact your local recycling center for

information on where to drop off the spent battery.

RBRC™ is a registered trademark of the

Rechargeable Battery Recycling Corporation.

Important Safety Instructions for Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for battery

chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery pack,

and product using battery pack.

DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe with

conductive objects.

WARNING: Shock hazard. Do not allow any liquid to get inside charger.

TRIGGER SWITCH

INTERRUPTEUR À DÉTENTE

GATILLO INTERRUPTOR

FORWARD/REVERSE BUTTON

INVERSEUR DE MARCHE

SELECTOR DE MARCHA HACIA

ADELANTE/REVERSA

BIT HOLDER

PORTE-LAMES

SUJETADOR DE PUNTAS

DEPTH

LOCATOR

LIMITEUR DE

PROFONDEUR

SENSOR DE

PROFUNDIDAD

BATTERY PACK

ENSEMBLE DE PILES

BATERÍA

ÍA

ADJUSTMENT COLLAR

BAGUE DE RÉGLAGE

COLLAR DE AJUSTE