DOD Rubberneck Analogue Delay Bruksanvisning
DOD
Inte kategoriserad
Rubberneck Analogue Delay
Läs gratis den bruksanvisning för DOD Rubberneck Analogue Delay (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 8.5 recensioner. Har du en fråga om DOD Rubberneck Analogue Delay eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
HOW IT WORKS:
Tap Ratio Switch:
This switch selects
between 3 dierent
tempo ratios making
it easy to get delay
repeats that are
perfectly in time with
the tapped intervals or
giving them a trip
doubled feel.
/Rubberneck
Rate Control:
This transparent pot utilizes a
bi-color LED beneath it to indicate
dierent delay operating states.
When it is green the delay eect
is enabled. When it is pulsing
green to yellow it is enabled and
showing the modulation Rate and
Depth settings. When it is red the
Rubbernecking feature is active.
The pot itself is used for selecting
the Rubberneck rate (time it takes
to modify the delay time when
the Eect footswitch is pressed
and held).
Tempo LED/Re
Adjust Contro
This transparent pot utilizes
an LED beneath it that ashes
at the current delay time. The
delay time can be changed
by tapping the Tempo/
Regen footswitch. The pot
itself is used for adjusting
the secondary regen/repeats
setting of the delay that is
enabled by pressing and
holding the Tempo/Regen
footswitch.
Tails Switch:
his switch allows
repeats to be heard or
not heard when the
delay is bypassed. The
3rd option (On-No Dry)
defeats the dry signal
while allowing delay
epeats to continue in
ypass.
Rate/Depth
Knobs:
These knobs control
the amount of delay
time modulation
creating sounds from
subtle chorusing to
wild vibrato/tremolo
textures.
Eect On
Footswitch:
This footswitch turns the
delay eect on and o.
When this footswitch
is pressed and held the
Rubbernecking feature is
enabled which modies
the delay time up or
down at dierent rates
depending on the setting
of the Rubberneck Rate
control.
Tempo/Regen
Footswitch:
This footswitch is used
to tap in the delay time
during performance.
When the delay is
enabled and the
footswitch is pressed, it
enables the secondary
repeats regen control
in the path providing
control of a secondary
delay repeats setting
set by the Regen Adjust
control.
Placement of the Rubberneck:
Rubberneck can be placed anywhere in
the signal path but it is recommended
as the last eect in the signal chain.
Gain/Tone Knobs:
The Gain knob shapes
the delay signal by
adding more input
gain into the bucket
brigades making the
delay more overdriven.
he Tone knob
ncreases brightens
or darkens the delay
ignal.
Repeats Knob:
This knob controls number of
delay repeats heard. Higher
settings can create oscillating
runaway feedback that analog
delays are known for.
Time Knob:
This knob controls the delay
time. Range is 30ms to
1000ms. Up to 1500ms of
delay is available using the
Tempo footswitch.
Level Knob:
This knob controls the output
level of the delay signal. Use
this in conjunction with the
Repeats, Tone and Gain knobs
to balance your delay levels.
Rubberneck |Analog Delay
Produktspecifikationer
| Varumärke: | DOD |
| Kategori: | Inte kategoriserad |
| Modell: | Rubberneck Analogue Delay |
Behöver du hjälp?
Om du behöver hjälp med DOD Rubberneck Analogue Delay ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad DOD Manualer
28 Januari 2025
23 September 2024
23 September 2024
8 September 2024
8 September 2024
8 September 2024
6 September 2024
6 September 2024
6 September 2024
5 September 2024
Inte kategoriserad Manualer
- Enphase
- Vogels
- Winegard
- Esotec
- Physa
- DMax
- Ninja
- Chief
- Pro-Ject
- Ernitec
- ATen
- Hovicon
- Nexxt
- Maestro
- ASSA ABLOY
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025