Draper Clarion 252133 Bruksanvisning
Draper
Projektionsduk
Clarion 252133
Läs gratis den bruksanvisning för Draper Clarion 252133 (2 sidor) i kategorin Projektionsduk. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 5 recensioner. Har du en fråga om Draper Clarion 252133 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Assembly/Mounting Instructions
Clarion Permanently Tensioned Projection Screen by Draper
Caution
① Read instructions through completely before proceeding.
② Follow instructions carefully. Installation con trary to instructions
invalidates warranty.
③ When lifting assembled screen, do not lift at only one corner; lift at
both corners. Lifting by one corner could result in damage to the
screen frame, especially on large screens.
④ Screen should be accessible for complete removal should fabric become
damaged or should other ser vice be required.
⑤ Screen should be installed level (using a carpenter’s level).
⑥ Nothing should be fastened to screen frame or viewing surface.
⑦ Make sure you have received all parts (see parts list below and exploded
diagram on page 2).
⑧ Screwdriver required for screen assembly; drill and screwdriver needed
for attachment to wall.
⑨ The ideal temperature range for assembling folding screens to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Copyright © 2011 Draper Inc. Form Clarion_Inst11 Printed in U.S.A.
®
If you encounter any diffi culties installing or ser vic ing your Clarion screen, call your
dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999; or fax (765) 987-7142.
Clarion—Hardware and Parts List
Frame Preparation
① Clean area and place frame assembly pieces face down. Snap plastic
corner pieces into ends of aluminum frame extrusions as indicated in
Figures 1 through 4.
Figure 1
② Check to verify that all four (4) plastic corners are seated securely in
aluminum frame extrusion lengths (see Fig. 5). Lock in place using eight (8)
self-tapping screws.
Caution: Do not over-tighten fasteners—over-tightening could caUse
damage to the frame corners.
Figure 2
Frame Extrusions - 4
Frame Corners - 4
Z-Brackets - 2
Viewing Surface - 1
Plastic Tubing - 4
Surface Retention
Extrusions- 4
Front
Back
Self-tapping
Screws-8
Figure 3
Figure 5
Figure 4
(Continued on Page 2)
Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310.
Produktspecifikationer
| Varumärke: | Draper |
| Kategori: | Projektionsduk |
| Modell: | Clarion 252133 |
Behöver du hjälp?
Om du behöver hjälp med Draper Clarion 252133 ställ en fråga nedan och andra användare kommer att svara dig
Projektionsduk Draper Manualer
22 September 2024
6 September 2024
4 September 2024
29 Augusti 2024
21 Augusti 2024
21 Augusti 2024
21 Augusti 2024
20 Augusti 2024
19 Augusti 2024
19 Augusti 2024
Projektionsduk Manualer
- GPX
- AWOL Vision
- Instaal
- Da-Lite
- Luxburg
- Oregon Scientific
- EluneVision
- Pyle
- Elite ProAV
- Lumene
- ORAY
- Elite
- AV:link
- Elite Screens
- Projecta
Nyaste Projektionsduk Manualer
3 April 2025
3 April 2025
2 April 2025
28 Januari 2025
11 Oktober 2024
6 Oktober 2024
2 Oktober 2024
29 September 2024
29 September 2024