Dunlop Crybaby Bruksanvisning
Dunlop
ej kategoriserat
Crybaby
Läs gratis den bruksanvisning för Dunlop Crybaby (4 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 32 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 16.5 recensioner. Har du en fråga om Dunlop Crybaby eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
The CRYBABY
®
has been a standard in the world
of music since its introduction in the late 1960's. Its
rugged construction and efficient design will give
years of outstanding performance.
OPERATING INSTRUCTIONS
•
By rocking your foot back and forth on the
pedal, you can change the effect that the
CRYBABY
®
has on the tone of your instrument
instantaneously. Toe down will give you more
treble, heel down will give you more bass. The
speed and amount of effect you use depends on
your style of playing.
•
When placing the pedal in one position, you will
hear a boost in that particular frequency. This
boost can be used to add sustain and create
feedback of a desired overtone.
TIPS
•
Listen to the classic recordings of Jimi Hendrix
and Eric Clapton where the CRYBABY
®
is used
extensively. After listening to the sound you will
begin to recognize the CRYBABY
®
in just about
every rock player's repertoire.
•
When using a lot of distortion, the effect will not
be as prominent. Try setting the pedal in one
position. This will help in making artificial
harmonics and controlling the amount of feedback.
CRYBABY
®
SET-UP INSTRUCTIONS
1. Insert a 9 volt battery and/or plug in AC
Adapter. The CRYBABY
®
will operate on either
power source.
Notice: This unit is shipped from the factory
without a battery to prevent possible damage
from leakage. A 9-volt transistor radio battery
must be installed for operation if an AC adapter
is not going to be used. We recommend a high
quality alkaline battery. The adapter jack
requires a 5.5/2.1mm coax plug. Most standard
9VDC AC adapters with greater than 20ma
current capability will work.
To install the battery, remove 4 screws from
the rubber feet securing the bottom cover and
insert the battery.
2. Run a cord from your instrument to the
CryBaby's Instrument jack.
3. Run another cord from your amplifier input
into the CryBaby's Amplifier jack.
4. Turn on the amplifier and begin playing.
5. To turn the pedal on, push the toe of the
pedal down again, until you feel another "click".
Jimi's preferred hookup was: Guitar to Fuzz to
CRYBABY® to Amplifier.
BATTERY
P.C. BOARD
Box 846 Benicia CA 94510 USA
–
+
Plug Polarity DC in 9 volts
FUZZ
CRYBABY
AMP
Produktspecifikationer
| Varumärke: | Dunlop |
| Kategori: | ej kategoriserat |
| Modell: | Crybaby |
Behöver du hjälp?
Om du behöver hjälp med Dunlop Crybaby ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Dunlop Manualer
9 Augusti 2025
8 Augusti 2025
ej kategoriserat Manualer
- Vertex Standard
- Planet
- SMAJAYU
- Proaim
- Summit
- Aqara
- Dutchbone
- LaCie
- Wohler
- Swann
- Philco
- Zelmer
- Loewe
- Smart-AVI
- MSolutions
Nyaste ej kategoriserat Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025