Durkopp Adler 1220 Bruksanvisning
Durkopp Adler
Symaskin
1220
Läs gratis den bruksanvisning för Durkopp Adler 1220 (70 sidor) i kategorin Symaskin. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 5 recensioner. Har du en fråga om Durkopp Adler 1220 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/70
1220-6/
122 -62
Manual, complete
All rights reserved.
Property of Dürkopp and protected by copyright. Any re of these contents, Adler G mbH use
including extracts, is prohibited without the prior written approval of Dürkopp Adler G .mbH
Copyright © Dürkopp Adler GmbH 2021
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
General safety instructions
The non-observance of the following safety instructions can cause
bodily injuries or damages to the machine.
1. The machine must only be commissioned in full knowledge of the
instruction book and operated by persons with appropriate
training.
2. Before putting into service also read the safety rules and
instructions of the motor supplier.
3. The machine must be used only for the purpose intended. Use of
the machine without the safety devices is not permitted. Observe
all the relevant safety regulations.
4. When gauge parts are exchanged (e.g. needle, presser foot,
needle plate, feed dog and bobbin) when threading, when the
workplace is left, and during service work, the machine must be
disconnected from the mains by switching off the master switch or
disconnecting the mains plug.
5. Daily servicing work must be carried out only by appropriately
trained persons.
6. Repairs, conversion and special maintenance work must only be
carried out by technicians or persons with appropriate training.
7. For service or repair work on pneumatic systems, disconnect the
machine from the compressed air supply system (max. 7-10 bar).
Before disconnecting, reduce the pressure of the maintenance
unit.
Exceptions to this are only adjustments and functions checks
made by appropriately trained technicians.
8. Work on the electrical equipment must be carried out only by
electricians or appropriately trained persons.
9. Work on parts and systems under electric current is not permitted,
except as specified in regulations DIN VDE 0105.
10. Conversion or changes to the machine must be authorized by us
and made only in adherence to all safety regulations.
11. For repairs, only replacement parts approved by us must be used.
12. Commissioning of the sewing head is prohibited until such time
as the entire sewing unit is found to comply with EC directives.
It is absolutely necessary to respect
the safety instructions marked by these signs.
Danger of bodily injuries !
Please note also the general safety instructions.
Produktspecifikationer
| Varumärke: | Durkopp Adler |
| Kategori: | Symaskin |
| Modell: | 1220 |
Behöver du hjälp?
Om du behöver hjälp med Durkopp Adler 1220 ställ en fråga nedan och andra användare kommer att svara dig
Symaskin Durkopp Adler Manualer
4 Mars 2025
20 Oktober 2024
17 Oktober 2024
17 Oktober 2024
13 Oktober 2024
11 Oktober 2024
6 Oktober 2024
28 September 2024
23 September 2024
23 September 2024
Symaskin Manualer
- Easymaxx
- Pfaff
- Kunft
- Kohler
- Silver
- LERAN
- Siemens
- Baby Lock
- Sinojo
- Bernina
- Aigger
- Feiyue
- Meister Craft
- Gritzner
- Lewenstein
Nyaste Symaskin Manualer
30 Juli 2025
24 Juli 2025
19 Juli 2025
19 Juli 2025
18 Juli 2025
10 Juli 2025
10 Juli 2025
10 Juli 2025
10 Juli 2025
21 Juni 2025