Durkopp Adler 610 Bruksanvisning

Durkopp Adler Symaskin 610

Läs gratis den bruksanvisning för Durkopp Adler 610 (134 sidor) i kategorin Symaskin. Guiden har ansetts hjälpsam av 6 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 3.5 recensioner. Har du en fråga om Durkopp Adler 610 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/134

610-01/630-01

Service Instructions

Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,

including extracts, is prohibited without the written approval in advance of Dürkopp Adler AG.

IMPORTANT

READ CAREFULLY BEFORE USE

KEEP FOR FUTURE REFERENCE

Table of Contents

Service Instructions 610-01/630-01 - 02.0 - 12/2016 1

1 About these instructions ........................................................... 5

1.1 Scope of the instructions .............................................................. 5

1.2 Representation conventions – symbols and characters ............... 5

1.3 Other documents .......................................................................... 6

1.4 Liability.......................................................................................... 7

1.4.1 Transport ...................................................................................... 7

1.4.2 Proper use .................................................................................... 7

2 Safety instructions ..................................................................... 9

2.1 Basic safety instructions ............................................................... 9

2.2 Signal words and symbols used in warnings.............................. 11

3 Working basis ........................................................................... 15

3.1 Sequence of settings .................................................................. 15

3.2 Laying the cables........................................................................ 15

3.3 Removing covers........................................................................ 16

3.3.1 Tilting and re-erecting the machine head ................................... 16

3.3.2 Removing and fitting the head cover .......................................... 17

3.3.3 Removing and fitting the arm cover............................................ 18

3.3.4 Removing and fitting the covers on the base plate..................... 19

3.3.5 Removing and inserting the throat plate..................................... 20

3.3.6 Removing and inserting the top feed foot and sewing foot......... 21

3.3.7 Removing and installing the feeds.............................................. 22

3.3.8 Removing and fitting the oil pan ................................................. 23

3.3.9 Removing and fitting the upper belt guard.................................. 24

3.3.10 Removing and fitting the lower belt guard .................................. 25

3.4 Removing disruptive components .............................................. 26

3.4.1 Removing and installing the thread cutter .................................. 26

3.4.2 Removing and installing the needle protection........................... 28

3.4.3 Removing and installing the looper and looper mounting........... 29

3.5 Flat surfaces on shafts ............................................................... 30

3.6 Locking the machine................................................................... 30

4 Gauge and key set.................................................................... 33

5 Setting the adjusting disk to the arm shaft crank ................. 36

6 Setting the holding position of the machine.......................... 38

7 Setting the lower toothed belt wheel ...................................... 39

8 Setting the sewing foot ............................................................ 40

8.1 Setting the sewing foot stroke .................................................... 40

8.2 Setting the speed of the sewing foot lifting ................................. 41

9 Setting the looper ..................................................................... 42

9.1 Setting the rocker bolt and the left lower shaft bearing .............. 42

9.1.1 Draining and filling the oil in the looper drive housing ................ 43

9.1.2 Removing and fitting the looper drive housing ........................... 44

9.1.3 Setting the left lower shaft bearing ............................................. 45

9.1.4 Setting the rocker bolt................................................................. 46

9.2 Setting the looper drive housing................................................. 48

9.3 Setting the needle evasive movement (ellipsis width) ................ 49

9.3.1 Setting the needle evasive movement........................................ 50

Produktspecifikationer

Varumärke:	Durkopp Adler
Kategori:	Symaskin
Modell:	610
Färg på produkten:	Groen
Vikt:	325 g
Bredd:	117 mm
Djup:	115 mm
Höjd:	40 mm
Ljusstyrka:	- cd/m²
Vattentät:	Ja
Fokus:	Centre
Förvaringsväska:	Ja
Stöd för stativmontering:	Ja
Halsord:	Ja
Närmaste fokusavstånd:	4 m
Prisma typ:	BaK-4
Förstoring:	8 x
Objektiv diameter:	26 mm
Gå ut eleven:	3.25 mm
Synfält (vid 1000 m):	118.6 m
Ögonlindring:	16 mm
Pupillavstånd (min):	56 mm
Oogafstand (max):	72 mm
Typ av ögonmussla:	Opdraaien
Schemer faktor:	14.42
Rengöringsduk:	Ja
Linsbeläggning:	Fully Multi Coated (FMC)
Linsskydd ingår:	Ja
Riktigt synfält:	6.8 °
Dioptrikompensation (±):	4