Eastron SDM630 Bruksanvisning
Eastron
Mätutrustning
SDM630
Läs gratis den bruksanvisning för Eastron SDM630 (4 sidor) i kategorin Mätutrustning. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 6.5 recensioner. Har du en fråga om Eastron SDM630 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
Voltage
input
Rated voltage
3×220/400V
Reference frequency
50Hz/60Hz
Power consumption
<2W
Current
input
Input current
0.5-10(100)A
Starting current
0.004Ib
Power consumption
<1VA (maximum current)
Pulse
Pulse width
200/100/60ms
Pulse constant
400imp/kWh
Communi-
cation
Interface
RS485(A+, B-)
Protocol
MODBUS, DL/T 645-2007
Overall
dimension
L×W×H
100mm×72mm×66mm
Maximum onnecting
capacity
Flexible cable
16mm^2
Temperature range
Working
temperature
-25 ~55℃ ℃
Storage
temperature
-40 ~70℃ ℃
Humidity
≤90%(no condensation)
Altitude
<2000m
Buttonicon
Button function
Selects the Voltage and Current display screens
In Set-up Mode, this is the “Left” or “Back” button.
Select the Frequency and Power factor display
screens
In Set-up Mode, this is the “Up” button
Select the Power display screens
In Set-up Mode, this is the “Down” button.
Select the Energy display screens
In Set-up mode, this is the “Enter” or “Right” button
1 3 5 N L1 L1' L2 L2' L3 L3' N'
A
B
C
N
1 3 5 N L1 L1' L2 L2' L3 L3' N'
A
B
C
N
***
. . .
B A - + - +
RS485 Clock1 pulse Clock2 pulse
G
1.LED status the indicator LED is flashing or off.:
Description:
( )1 the red light is pulse output. the flash frequency of the red light
can show the power strength. the bigger power measured,the red
light will flash faster.
2 Fault description the measurement is not inaccurate.. :
Suggestion check the wiring of inlet and outlet of energy meter: .
Namely make sure that the wiring of A B C three phase of energy, / / ( )
/ / meter is matched with the A B C phase of utility grid.
3.Fault description the energy meter failed to communicate with :
SPH.
Suggestion:
( ) “ “ “ “1 check the CT mode of SPH is energy meter mode .
( ) + - 2 check the voltage between A and B is within the range of
+( . ~ . )4 4 4 5 V
( ) . 3 check the RS485 communication cable is right That is to say
the A B of energy meter is matched to A B of SPH Also +/ + +/ - . ,
make sure the wiring is fixed firmly .
a When SPH series products are used in three phase power grid. -
, “ “ system please set the CT mode” of SPH as Meter Mode”.
More details please refer to SPH user manual. ,
b. When connecting three-phase energy meter, SPH gets the
information of the sum of three-phase active power to process the
logical control by RS485 communication.
Note: We describe Growatt-SPH6000 and Growatt-SPH11000
TL3-HV as “SPH” as below.
d.Connect the end of the RS485 cable to SPH RJ45(Sensor)
port.
e. Connect the A+ of RS485 cable to Pin7 and B- of it to Pin8.
Me te r
Lo ad
RS -4 85
∑ ≥P 0 , Charge
∑ ≤P 0 , Di scha rge
L1
L2
L3
N
Produktspecifikationer
| Varumärke: | Eastron |
| Kategori: | Mätutrustning |
| Modell: | SDM630 |
Behöver du hjälp?
Om du behöver hjälp med Eastron SDM630 ställ en fråga nedan och andra användare kommer att svara dig
Mätutrustning Eastron Manualer
1 Januari 2025
16 September 2024
13 September 2024
4 September 2024
20 Augusti 2024
20 Augusti 2024
16 Augusti 2024
15 Augusti 2024
12 Augusti 2024
10 Augusti 2024
Mätutrustning Manualer
- Laserliner
- Topex
- Basetech
- Silvercrest
- Hikmicro
- VDO
- Intact
- Be Cool
- Hameg
- Soler And Palau
- Goclever
- MSW
- Hanna
- Zircon
- TFA Dostmann
Nyaste Mätutrustning Manualer
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025