Edwards Signaling 5532M Bruksanvisning

Edwards Signaling mottagare 5532M

Läs gratis den bruksanvisning för Edwards Signaling 5532M (10 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.1 stjärnor baserat på 10.5 recensioner. Har du en fråga om Edwards Signaling 5532M eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/10

5540M Tone Generator and 5532M

Speaker/Amplifier Installation Sheet

Description

Edwards Tone Generator and Speaker/Amplifiers are

intended for industrial applications where high audible output

and microcomputer reliability are required. The Adaptatone

Millennium Series are UL and cUL Listed as Audible Signal

Appliances for use in the hazardous locations listed in

Table 1.

The 5532B Speaker/Amplifiers are UL Listed and CSA

Certified as Audible Signaling Appliances.

The 5532M-Y6 is additionally UL Listed in a Speaker and

Amplifier category, when powered with 120V/240 VAC 50/60

Hz, for use in conjunction with the 5541M-Y6 Millennium

System Master either for emergency/evacuation, non-fire, or

for supplementary fire alarm control panel accessory

applications (see Instructions for 5541M-Y6, part 3100471).

The Tone Generator operates from local power. It

accommodates up to four normally-open contacts on its

inputs. The tone that sounds in response to an active input

is determined by setting miniature programming switches

inside the unit. Table 6 has switch settings for setting tones.

Four tones may be programmed into the Tone Generator at

any time. These tones operate on a pyramid-type priority

system. The tone programmed on SW1 overrides the tones

programmed on SW2, SW3, and SW4. The tone on SW2

overrides the tones programmed on SW3 and SW4.

Likewise, the tone on SW3 overrides the tone programmed

on SW4. The tone programmed on SW4 has the lowest

priority and cannot override any other programmed tone.

Speaker/Amplifiers are heavy-duty, stand-alone signaling

devices that operate from local power and sound a tone

programmed at the Tone Generator. Speaker direction and

the output level are easily adjustable. Up to 2500 of these

Speaker/Amplifiers can be connected in parallel to the tone

output of a single tone generator.

Recording a Voice Message (5540MV

Series)

WARNING: High voltage is present when product is

energized.

Four five-second messages (or one twenty-second

message) can be recorded on the voice module unit. Refer

to Figure 16.

1. Put switches A and B on the programming dipswitch in

the proper position for the message to be recorded

(Figure 16). For programming a message longer than

five seconds, use Message Location 1.

Message

Location

Start Switch A

Settings

Switch B

Settings

1 0 Sec CLOSED CLOSED

2 5 Sec OPEN CLOSED

3 10 Sec CLOSED OPEN

4 15 Sec OPEN OPEN

2. Put switch PGM on the programming dipswitch in the

“CLOSED” position for programming mode (Figure 16).

3. Press and hold the record button while speaking clearly

into the microphone to record your message. Release

the button when recording is complete.

4. To test the message, press and hold PLAY while in

programming mode.

NOTE: This will play only the current location.

WARNING: High volume may cause harm to personnel in

close proximity.

5. Adjust the volume as necessary. Set the main volume

using the potentiometer on the main board (Figure 14 -

Figure 16) and then set the voice volume using the

potentiometer on the voice module board (Figure 16).

Produktspecifikationer

Varumärke:	Edwards Signaling
Kategori:	mottagare
Modell:	5532M
Vikt:	68 g
Bredd:	20 mm
Djup:	180 mm
Höjd:	120 mm
Förpackningens vikt:	169 g
Förpackningens bredd:	219 mm
Djuppackning:	162 mm
Förpackningshöjd:	47 mm
Certifiering:	CE, FCC
Hållbarhetscertifikat:	RoHS
Förvaringstemperatur:	-25 - 70 °C
Internera:	Ja
Stöder Mac-operativsystem:	Mac OS X 10.10 Yosemite, Mac OS X 10.11 El Capitan, Mac OS X 10.8 Mountain Lion, Mac OS X 10.9 Mavericks
Stöder Linux:	Ja
Snabbinstallationsguide:	Ja
Värdgränssnitt:	PCIe
Serveroperativsystem som stöds:	Windows Server 2008 R2, Windows Server 2012
Chipset:	Marvell - 88SE9230
Typer av RAID:	0, 1,10, JBOD
(Ytter) huvudpaketets höjd:	357 mm
(Ytter) huvudförpackningens bredd:	465 mm
(Ytre) huvudpaketets längd:	500 mm
Kvantitet per (yttre) huvudkartong:	40 stuk(s)
Drifttemperatur (TT):	5 - 50 °C
Relativ luftfuktighet i drift (VV):	20 - 80 procent
Harmoniserad systemkod (HS):	84733020
Expansionskorts formfaktor:	Volledige hoogte / Laag profiel
Expansionskort standard:	PCIe 2.0
Dataöverföringshastighet (max):	6 Gbit/s
Antal interna SATA-portar:	2
SATA-revision:	3.0
Utgångsgränssnitt:	M.2
Portmultiplikator:	Ja