EK Water Blocks EK-FB ASUS R4BE Bruksanvisning

EK Water Blocks Hårdvarakylning EK-FB ASUS R4BE

Läs gratis den bruksanvisning för EK Water Blocks EK-FB ASUS R4BE (2 sidor) i kategorin Hårdvarakylning. Guiden har ansetts hjälpsam av 21 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 11 recensioner. Har du en fråga om EK Water Blocks EK-FB ASUS R4BE eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

All disclosures, noces and warranty condions are being wrien on EKWB web page. Please check terms of use. Revision 1.0. Published on December 20

2013

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at for updates. Before www.ekwb.com

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK High Flow and EK-CSQ type fittings require only a small amount of force to screw them firmly place since the liquid seal is ensured by the rubber o-ring gaskets.in

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Rampage IV Black Edition motherboard

STEP 1: PREPARING YOUR MOTHERBOARD

STEP 2: REMOVING THE ORIGINAL LATCH MECHANISM

1. REMOVING STOCK COOLER. Remove all encircled screws. There are 13 screws on the back of

the motherboard that needs to be removed in order to remove the factory installed SB/MOSFET heat

pipe cooling solution.

Please remove your motherboard from the computer to assure safest

mounting process possible in order to prevent any possible damages to

your PCB. With the enclosed Torx T20 key please remove all four (4)

screws securing the socket latch mechanism (ILM) to original backplate

(BP) to the motherboard. Make sure you have install the plastic

cover over the socket pins and that the socket latches are in

OPEN position during this procedure!

STEP 3: INSTALLING ALTERNATIVE LGA-2011 BACKPLATE

STEP 4: PREPARING YOUR MOTHERBOARD

After removing the original LGA-2011 backplate, installed on your ASUS Rampage IV Black Edition

motherboard, it is mandatory to install the alternative LGA-2011 provided with your motherboard.

Use the enclosed Torx T20 key to re-install it. Make sure you have install the plastic cover

over the socket pins and that the socket latches are in OPEN position during this

procedure! It is now a prime time to install your LGA-2011 CPU into the motherboard socket.

2. CLEANING THE PCB. Carefully detach the original stock cooler after

removing screws securing it to the board. Wipe off the remains (by all

using non abrasive cloth or –

qtip

, as shown on sample photo) of the

original thermal compound until the components and circuit board are

completely clean. EKWB recommends the use of denatured alcohol for

removing TIM leftovers.

3. APPLYING THERMAL COMPOUND. Apply thermal compound:

lightly coat the Intel X79 (PCH) see sample photo on the left and –

CPU heat spreader (IHS) - see sample photo on right with

enclosed -TIM Ectotherm thermal grease. EK

The quantity of about two rice grains is just about right. There is no need to cover the

whole IHS. Applying too much thermal grease will have negative impact on the cooling

performance!

Installation manual for water block EK- ASUS R4BE Monoblock FB

X79 PCH (SB)

CPU socket

Mosfets

IMPORTANT NOTICE:

ROG LED (Logo) has to be removed in order to

successfully complete installaon of the FB KIT

ASUS R4BE and cannot be used in combinaon

with the FB KIT ASUS R4BE.

Use plasc

socket cover

during install!

Do not

remove the

X79 PCH (SB)

backplate!

Produktspecifikationer

Varumärke:	EK Water Blocks
Kategori:	Hårdvarakylning
Modell:	EK-FB ASUS R4BE
Modell:	Vattenblock
Kompatibla produkter:	ASUS Rampage IV Black Edition
Lämplig placering:	Moderkort
Vattenblocksmaterial:	Koppar