Electrolux E2YH01 Bruksanvisning
Electrolux
Järn
E2YH01
Läs gratis den bruksanvisning för Electrolux E2YH01 (20 sidor) i kategorin Järn. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 2 recensioner. Har du en fråga om Electrolux E2YH01 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/20
MOUNTING INSTRUCTIONS
INSTRUCTIONS DE MONTAGE
MONTAGEANLEITUNG
INSTRUCTIES VOOR MONTAGE
INSTRUZIONI PER IL MONTAGGIO
INSTRUCCIONES DE INSTALACIÓN
INSTRUÇÕES DE MONTAGEM
MONTERINGSANVISNINGER
MONTERINGSINSTRUKSJONER
MONTERINGSANVISNING
ASENNUSOHJEET
Инструкция по монтажу
MONTAJ BILGILERI
EN
DE
FR
IT
NL
PT
ES
NO
DA
FI
SV
EL
RU
TR
2.
3. 4.
1.
5. 6.**
112233
445566
66**77
8899
Dear customer,
this discharging kit will allow your tumble dryer to discharge the condensation water produced
during each drying cycle directly into the nearest drain, without your having to empty out the
tank at the end of the cycle.
Open the door of your tumble dryer, and extract from the drum the bag that contains the
following items of the discharging kit:
●a nylon band;(5)
●a 90° fitting for connecting the draining hose;(3)
●a plastic curved part to be used for discharging into a sink;(2)
●a plastic anchoring support for fastening the draining hose to the back of the
machine;(4)
●2,5 metres of semi-transparent hose;(1)
●a gasket.(6**)
Position the tumble dryer so its back is towards you.
At the top right you can see a red hose which comes out of the back and is fastened to
a plastic fitting.
Using a pair of pliers, loosen the metal band and push it down, in order to be able to
extract the red hose from the plastic fitting.
Take the 90° fitting that has been supplied and insert it into the red hose.
Insert the plastic anchoring support that fastens the draining hose to the back, then
connect the other end of the draining hose to the 90° fitting.
Using the nylon band, fasten the red hose to the fixed fitting on the back.
By means of a 7-mm socket spanner, unscrew the screw shown in the figure from the
back. Insert the screw you have removed into the relevant seat on the plastic anchoring
support, and tighten the screw, positioning the draining hose as shown in the figure.
If necessary, shorten the draining hose. If you wish to discharge the condensation water
into a sink, you will have to apply the plastic curved part to the draining hose, in order
to be able to hang it on the edge of the sink.
Important!
Do not hang the curved part at a height exceeding 1 metre, and suitably shorten the
draining hose so as not to create a bend higher than 0.5 metres, as shown in the figure.
* Dryers with Steam Technology
Important!
The operation described below must be carried out before completing the stages of the entire
installation of the tumble dryer.
11
22
33
44
55
66
77
88
99
66**
** only with kit 12512251/
E
EN
N
Produktspecifikationer
| Varumärke: | Electrolux |
| Kategori: | Järn |
| Modell: | E2YH01 |
Behöver du hjälp?
Om du behöver hjälp med Electrolux E2YH01 ställ en fråga nedan och andra användare kommer att svara dig
Järn Electrolux Manualer
8 Februari 2025
8 Februari 2025
8 Februari 2025
8 Februari 2025
8 Februari 2025
25 Juli 2024
24 Juli 2024
19 Juli 2024
19 Juli 2024
19 Juli 2024
Järn Manualer
- Eudora
- Black And Decker
- Matsui
- Becken
- Mellerware
- Arzum
- Thomas
- Di4
- Comelec
- Inventum
- Vanguard
- Zelmer
- Brentwood
- Maxwell
- Currys Essentials
Nyaste Järn Manualer
5 April 2025
1 April 2025
1 April 2025
31 Mars 2025
31 Mars 2025
12 Mars 2025
5 Mars 2025
5 Mars 2025
5 Mars 2025
5 Mars 2025