Electrolux EWE361KA-DWB6 Bruksanvisning

Electrolux Pannor & pannor EWE361KA-DWB6

Läs gratis den bruksanvisning för Electrolux EWE361KA-DWB6 (2 sidor) i kategorin Pannor & pannor. Guiden har ansetts hjälpsam av 8 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 4.5 recensioner. Har du en fråga om Electrolux EWE361KA-DWB6 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

EN ELECTRIC WATER HEATER USER MANUAL

1. PARTS IDENTIFICATION

1. Front Cover

2. LED Indicators

i) Earth LED Indicator

ii) Power/ELCB LED Indicator

3. Test / Reset Button

4. Face Panel

5. Pump Button*

6. Temperature Control Knob

7. 3 in 1 Stop Valve

i) Stop Valve Lever

ii) Flow Regulator Valve Adjustment

iii) Built-in-Filter

8. Mesh Filter

9. Rail Support

10.

Handshower

11. Adjustable Shower Holder

12. Slider Rail

13. PVC Hose

14. Soap Tray

15. Heater Base

16. Terminal Block

17. Thermostat (Double-Action)

18. Heater Tank

19. PCB Board (Test & Reset)

20. VR Board

21. Main/ELCB Board**

22. Water Outlet Connection

23. AC Pump*

24. TRIAC

25. Reed Switch Assy***

26. Water Inlet Connection***

27. SMPS PCB Board

28. D.C. Silent Pump*

29. Rating Label

30. Pump Board

31 Shower Bracket Holder

SAFETY INFORMATION

2.1 Products manufactured by Electrolux are safe

provided they are installed, used and maintained

in good working order in accordance with our

instructions and recommendations. Always refer

to this manual if you have any doubt.

2.2 The Electric Water Heater must be earthed.

Improper grounding could cause electrical shock.

2.3 If any of the following conditions occur as

shown below, immediately switch off the power

supply and contact the Electrolux Consumer

2.6 When the Electric Water Heater is

used by someone such as child, elderly

person, sick person and physically

handicapped person, the person

concerned is kindly requested to pay

attention and check the shower

temperature by hand from time to time.

2.7 During lightning/thunder, switch off the power

supply to the Electric Water Heater in advance to protect

the Electric Water Heater against possible damage.

2.8 The earth continuity conductor of the electrical

installation must be effectively connected to all

exposed metal parts of other appliances and

services in the room, which in the Electric Water

Heater is to be installed to conform to local

regulations and ensure proper earthing/grounding

for ELCB to be effective.

NOTE : When removing the Electric Water Heater

from package, a small amount of water may be

found inside. This is normal as the Electric Water

Heater is tested during manufacturing process.

WARNING !

If the Electric Water Heater begins to make an

odd noise, smell or smoke.

If ELCB trips and Electric Water Heater Indicator

does not light up.

Water temperature cannot be controlled.

If the Electric Water Heater shows signs of a

distinct change in performance.

If water leaks from inside.

2.10 Installation must be carried out by a

quali ed personnel and in compliance local ﬁ

2.11 This Electric Water Heater must be

permanently connected to the direct main line

supply. A plug and socket is not recommended

to be used.

2.12 For the correct size of wire conductor

corresponding to different electrical loadings,

2.13 This Electric Water Heater operates at a

minimum water ﬂow rate of 2.0 litre/min

and maximum working

2.14 The Electric Water Heater will not function

if there is insuf cient water ow (min 2.0 litre/minﬁ ﬂ

2.15

The built-in ELCB will automatically cut off

the power supply in case there is a current

2.16

The thermostat will automatically cut off the

power supply if it has sensed an abnormal rise in

water temperature.

CAUTION !

authority regulations.

please refer to Table 1.

pressure of 6 bars.

For direct connection from the water tank, the

Electric Water Heater must have an installation

minimum 1.0m below the water tank.

leakage over 15mA.

Care Center. Never attempt to repair the Electric

Water Heater yourself:

2.5 For Pump Model, it is highly recommended

to connect the Water Inlet Connection to tank

storage supply, otherwise it may cause damage

to the Pump Motor.

User is advised to test and adjust the

water temperature before using.

2.9 WARNING : Metallic / chromed hose and

conductive control valve shall not be used.

3. ELECTRIC WATER HEATER UNIT INSTALLATION

3.1 Select a suitable position in the bathroom.

3.2 Remove the screw (A) at the bottom of the

Electric Water Heater

. (Fig. 2)

3.3 Remove the Front Cover from the bottom and then lift up the front cover.

3.4 Mark 3 Screw points of the Heater Base on the wall. The

Electric Water Heater

position should be

1.5m above the bathroom floor. (Fig. 2)

3.6 Use 6mm diameter drill and make the wall plug holes in depth of 34mm ,for mount the Electric

Water Heater.

3.7 Insert the wall plugs and mount the

Electric Water Heater

firmly in position with the screws provided.

3.8 Insert the Shower Holder and Soap Tray into the Slider Rail.

3.9 Insert the Rail Bracket to both end of the Slider Rail Bar.

3.10 Remove the cap from the Rail Bracket and screw the Bracket to marked position.

Replace the cap. (Fig. 3)

connect to

water outlet

connection

ELECTRIC WATER HEATER

UNIT INSTALLATION DIAGRAM

Fig. 2

Screw

3 in 1

stop valve

inlet

Wall

285.5mm

Washer

connect to

water inlet

connection

Min.

80 mm

150mm

4. PLUMBING PROCEDURE

CAUTION!

IMPORTANT

This Electric Water Heater is a single point

system and the “Water Outlet” can only be

fitted to the Hose and Handshower set

provided. MUST NOT TO CONNECT

CONTROL VALVE OR FITTING CAN BE

FITTED TO THE WATER OUTLET.

WARNING!

ELECTRICAL INSTALLATION

WARNING!

PROCEDURE :

5.7 Connect the cable as following: (Fig. 5)

BROWN or RED --LIVE (L)

BLUE or BLACK --NEUTRAL (N)

GREEN or GREEN/YELLOW --EARTH ( )

5.8 Clamp the cable to the correct position.

Technician need to confirm the wire before

installation.

CHECK IF THE WIRING CONNECTION IS

CORRECT and replace the cover.

5.9 When putting back the Front Cover,

please take note of the procedure shown below :

-Ensure the position is correct, turn the

Temperature Control Knob Insert to OFF

position as shown in Fig.A (At the Heater Base)

-Install the Front Cover,turn the Temperature

Control Knob to OFF position to align with the

VR shaft as shown in Fig.B (At the Front Cover)

5.10 Fix the Temperature Control Knob and

screw ‘A’ (Fig. 2).

5.1 This Electric Water Heater must be

earthed. Improper grounding could cause

electrical shock.

5.2 Remember to SWITCH OFF the power

supply before carrying out any electrical work.

5.3 Refer to TABLE 1 for the correct cable size.

5.4 Use double insulation cable of over 2.5mm²

for 2.4kW, 3.5kW 3.8kW, 4.5kW 4.8kW models

and 4mm² for 3.6kW and 6.0kW model.

5.5 Lead the power cable from MCB to a

“ON/OFF’’ double pole Linked Switch having a

contact separation of at least 3mm in all poles

outside the bathroom, then lead a cable to the

terminal block inside the Electric Water Heater.

(Fig. 4)

5.6 Insert the wall embedded cable through

Side Entry ‘A’ by cutting a hole at the source

cord rubber holder and lead the cable to

Cable Bracket ‘B’. (Fig. 6)

Always KEEP the water supply to the Electric Water

Heater free from mud and dirt at all time during usage.

4.1 Connect the 3 in 1 Stop Valve to the Water

Inlet with washer. Use correct tools to tighten

and be careful not to over tighten and damage

the plastic nut.

4.2 Connect the incoming water piping to the 3 in

1 Stop Valve (1/2” BSP).

Make sure to put the Mesh Filter between 3

in 1 Stop Valve and incoming water piping.

4.3

If in any case, the 3 in 1 Stop Valve is not use or

omitted, make sure to put the Mesh Filter

between the Electric Water Heater inlet pipe

and incoming water pipe.

4.4 Turn on the water mains to drain out all plumbing

dirts before connecting the water supply to the

Electric Water Heater, the water supply to the

Electric Water Heater must be free from mud and

dirt.

4.6 Hook the Handshower to the Slider Rail

Shower Holder and adjust to your ideal position.

4.7 Check if any water leakage.

4.8 Do not use sealing tape during piping

installation.

THE HEATER TANK MUST BE FILLED UP WITH

WATER BEFORE TURNING ON THE POWER

SUPPLY TO PREVENT ANY DRY BURNT DAMAGE

TO THE HEATING ELEMENT.

4.5 Connect the Hose and Handshower to the

outlet of Electric Water Heater, be sure to put in the

Washer in between the connection. (Fig. 2)

4.10 DO NOT APPLY PLUMBING CEMENT ON

CONNECTION. WHENEVER NECESSARY, USE

ONLY THREAD OR SEALING TAPE.

4.9 THE WATER INLET AND OUTLET MUST BE

INSTALLED CORRECTLY, OTHERWISE ELECTRIC

WATER HEATER WILL NOT FUNCTION.

5. ELECTRICAL INSTALLATION (CONT’D)

6. TABLE 1 - CABLE SIZE TABLE

Power Current

(kW) (A)

220V ~

50/60 Hz

Conductor Size (csa)

mm Conduit Cable Flexible Cable

On/ Off Fuse /

Switch (A) MCB (A)

2.4 10.9 2.5 7 / 0.67mm 50 / 0.25 mm 20 20

3.5 15.9 2.5 7 / 0.67mm 50 / 0.25 mm 20 20

4.5 20.5 2.5 7 / 0.67mm 50 / 0.25 mm 32 32

6.0 27.3 4.0 7 / 0.85mm 56 / 0.30 mm 32 32

Voltage

(AC)

3.6 15.0 4.0 7 / 0.85mm 56 / 0.30 mm 20 20

240V ~

50/60 Hz

(Malaysia Model)

METHOD OF ALIGNMENT WHEN REPLACING FRONT COVER

Cable

Fig. 4

Brown or Red = Live (L)

Blue or Black = Neutral (N)

Green or Green/ Yellow = Earth ( )

Fig. 5

Fuse Distributor Board

Miniature Circuit Breaker (MCB)

ON/OFF Double Pole Switch

Double PVC cable

NOTE:

Refer to TABLE 1 for electrical loading and

correct size of wire conductor

Fig. 6

Front CoverFig A Fig B

Position

this Way

Position

this Way

1 2

3 4 5

(2.2 ℓ/Min for 4.8kW & 2.5 ℓ/min for 6.0kW model

only)

/ 2.2 ℓ/Min for 4.8kW & 2.5 ℓ/min for 6.0kW model

only) to trigger the flow switch.

REV 1

Fig. 3a

(Thailand, Indonesia, Philippines,

and Malaysia pump model)

SHOWER SET INSTALLATION DIAGRAM

Fig. 3b

(Malaysia standard model)

SHOWER SET INSTALLATION DIAGRAM

Cap

Screw

Rail Bracket

Adjustable

Shower

Holder

Wall Plug

Slider

Rail Bar Flexible Angle

Adjustment

Flexible

Hose

Hand

Shower

PVC Hose

Shower

Screw

Shower

Holder

Cover

Shower

Holder

Cover

Head

SLIDER BAR ACCESSORIES

(Single Spray)

BRACKET ACCESSORIES

(Single Spray)

3.5. : Mark 2 screw points of the Slider Rail beside the Electric Water Heater. Slider Bar Accessories

It is recommended that the top of the portion is in level with the top of Electric Water Heater. (Fig. 3 & 3a)

Bracket Accessories: Open the Shower Holder cover, mark 2 screw point of the Shower Holder beside

the Electric Water Heater. It is recommended that the top of the portion is in level the top Electric

Water Heater. After screw the Shower Holder, put back the shower holder cover. (Fig. 3b)

EWE361KA-DWG6

EWE381KX-DWG6

EWE481KX-DWG6

EWE601KX1DWG6

EWE351KX-DWX6

EWE361KA-DWP6

EWE451KX-DWB2

EWE241KX-DWB6

EWE351KX-DWB6

EWE451KX-DWB6

EWE361KA-DWB6

EWE361KX-DWB5

EWE361KX-DWX5

3.8 17.3 2.5 7 / 0.67mm 50 / 0.25 mm 20 20

4.8 21.8 2.5 7 / 0.67mm 50 / 0.25 mm 32 32

2.4 If the Red (POWER) Indicator does not go off

when you turn off the water, switch OFF the

mains supply and contact Electrolux Consumer

Care Centre for repair service.Special skill is

required for repairing.

NEVER try to repair the unit by yourself.

No Pump model

AC Pump model DC Pump model

Fig. 1

17 17

* For Pump Model only

** Pump Model VR Board & Main/ELCB Board combine.

Slider Bar Accessories

(Single Spray)

Bracket Accessories

(Single Spray)

Slider Bar Accessories

* ** * **

** **

Fig. 3 (Vietnam only)

SHOWER SET INSTALLATION DIAGRAM

Flexible

Angle

Adjustment

5 Spray

Patterns

Selection

Hand

Shower

Flexible

Hose

Soap

Tray

Slider

Rail Bar

Adjustable

Shower

Holder

Screw

Wall

Plug

Mounting

Terminal

connect to

water outlet

connection

Rail bracket

cap

Hexagon tool

(Tighten plastic nut before close cap)

Plastic nut

Fig 3C

RAIL BRACKET COVER & CAP DISMANTLE STEPS FOR SLIDER BAR ACCESSORIES

1RAIL BRACKET 2

OPEN THE RAIL

BRACKET COVER

BY TURNING ANTI

CLOCKWISE & USING

SCREW DRIVER TO OPEN

THE CAP

3RAIL BRACKET

COVER COME-OUT

Fig 1.

Slide Bar Accessories (Vietnam only)

Slide Bar Accessories (Single Spray – Thailand, Indonesia, Philippines, and Malaysia pump model)

Bracket Accessories (Single Spray – Malaysia standard model)

***

*** No pump Model 4.8kW & 6.0kW using Flow Sensor Assembly.

Produktspecifikationer

Varumärke:	Electrolux
Kategori:	Pannor & pannor
Modell:	EWE361KA-DWB6
Färg på produkten:	Zilver
Vikt:	1200 g
Bredd:	290 mm
Djup:	197 mm
Höjd:	15.8 mm
Husmaterial:	Glass fibre, Polyamide
Blåtand:	Ja
Sensor för omgivande ljus:	Ja
Skärm diagonal:	11.6 "
Upplösning:	1920 x 1080 Pixels
Pekskärm:	Ja
Original bildförhållande:	16:9
Gyroskop:	Ja
Accelerometer:	Ja
Processorfrekvens:	0.8 GHz
Processorfamilj:	Intel® Core™ M
Processormodel:	M-5Y10c
Antal processorkärnor:	2
Wi-Fi-standarder:	802.11a, Wi-Fi 5 (802.11ac), 802.11b, 802.11g, Wi-Fi 4 (802.11n)
Vormfaktor:	Convertible (Map)
Främre kameraupplösning (numerisk):	1 MP
Inkluderar operativsystem:	Windows 8.1
Ethernet LAN:	Nee
Integrerad minneskortläsare:	Ja
Kompatibla minneskort:	MMC, SD, SDHC, SDXC
Typiskt kontrastförhållande:	800:1
Touch-teknik:	Multi-touch
Ljusstyrka:	270 cd/m²
Pekskärmstyp:	Capacitief
Processor litografi:	14 nm
LED-bakgrundsbelysning:	Ja
Antal USB 2.0-portar:	2
DVI-port:	Nee
Antal inbyggda högtalare:	2
Lösenordsskydd:	Ja
HD typ:	Full HD
Inbyggd mikrofon:	Ja
Internminne:	4 GB
Förvarings media:	SSD
Batteritid/batteritid:	6.5 uur
Internminnestyp:	DDR3L-SDRAM
Password bescherming:	SSD, Supervisor
Hållbarhetscertifikat:	RoHS, ENERGY STAR
Inkluderad programvara:	Veriface Pro, Zinio Online NLenovo® Photo Masterewsstand, OneKey Optimizer, Evernote, Lenovo SHAREit, Lenovo Hamony,
Intel® Wireless Display (Intel® WiDi):	Ja
Antal portar USB 3.2 Gen 1 (3.1 Gen 1) Typ A:	1
Processoruttag:	BGA 1234
Stepping:	F0
Systembuss:	- GT/s
Processor antal trådar:	4
PCI Express-kortplatsversion:	2.0
Processorns driftlägen:	32-bit, 64-bit
Processorns cache:	4 MB
Tjunction:	95 °C
Thermal Design Power (TDP):	4.5 W
Kodnamnsprocessor:	Broadwell
Maximalt antal PCI Express-linjer:	12
Typ av processorcache:	L3
ECC stöds av processor:	Nee
Processorfabrikant:	Intel
Konfigurerbar TDP-ned:	3.5 W
Konfigurerbar TDP ned frekvens:	0.6 GHz
Konfigurerbar TDP-uppfrekvens:	1 GHz
Konfigurerbar TDP-up:	6 W
Operativsystems arkitektur:	64-bit
Provprogram:	McAfee LiveSafe, Microsoft Office
Maximalt internminne:	8 GB
Total lagringskapacitet:	128 GB
Typ av optisk enhet:	Nee
Inbyggd grafikadapter:	Ja
Separat grafikadapter:	Nee
Familjens inbyggda grafikadapter:	Intel® HD Graphics
Inbyggd grafikadaptermodell:	Intel® HD Graphics 5300
Grundläggande frekvens inbyggd grafikadapter:	300 MHz
Inbyggd grafikadapter dynamisk frekvens (max):	800 MHz
Inbyggt grafikkort-ID:	0x161E
Maximalt minne inbyggd grafikadapter:	16 GB
Inbyggd grafikadapter DirectX-version:	11.2/12
Inbyggd grafikadapter OpenGL version:	4.3
Fram kamera:	Ja
Numerisk knappsats:	Nee
Instruktionsuppsättningar som stöds:	AVX 2.0, SSE4.1, SSE4.2
Intel® Smart Response Technology:	Ja
Intel® Hyper Threading Technology (Intel® HT Technology):	Ja
Intel® Turbo Boost-teknik:	2.0
Intel® Quick Sync-videoteknik:	Ja
Intel® InTru™ 3D-teknik:	Ja
Intel® Clear Video HD-teknik (Intel® CVT HD):	Ja
Intel® Insider™:	Ja
Intel® Flex Memory Access:	Ja
Intel® AES nya instruktioner (Intel® AES-NI):	Ja
Förbättrad Intel SpeedStep-teknik:	Ja
Kör Disable Bit:	Ja
Idle stater:	Ja
Termisk övervakningsteknik:	Ja
CPU-konfiguration (max):	1
Intel® Enhanced Halt State:	Ja
Intel® VT-x med utökade sidtabeller (EPT):	Ja
Inbyggda alternativ tillgängliga:	Nee
Grafik & IMC litografi:	14 nm
Intel® Small Business Advantage (Intel® SBA):	Ja
Intel® Secure Key:	Ja
Intel® 64:	Ja
Intel® OS Guard:	Ja
Intel® Virtualization Technology for Directed I/O (VT-d):	Ja
Intel® Virtualization Technology (VT-x):	Ja
Processorpaketstorlek:	30 x 16.5 mm
Konfliktfri processor:	Ja
Intel® Identity Protection Technology (Intel® IPT):	Ja
Versie Intel® Identity Protection Technology:	1.00
Versie Intel® Secure Key Technology:	1.00
Versie Intel® Smart Response Technology:	1.00
ARK ID-processor:	85234
Intel® Trusted Execution Technology:	Nee
Intel® TSX:	Nee
Intel® Stable Image Platform Program (SIPP):	Nee
Versie Intel® Stable Image Platform Program (SIPP):	0.00
Intel® TSX-NI-version:	0.00
Anslutning till basstation:	Nee
Kombinerad hörlurs/mikrofonport:	Ja
Maximal processorturbofrekvens:	2 GHz
Processorkod:	SR23C
Diskret grafikadaptermodell:	Niet beschikbaar
Antal installerade SSD:er:	1
SSD-kapacitet:	128 GB
Pekdon:	Touchpad
Windows-tangenter:	Ja
Klockhastighetsminne:	1600 MHz
Minneslayout:	1 x 4 GB
Minnesformfaktor:	On-board
SSD-formfaktor:	M.2
SSD-gränssnitt:	M.2
Tangentbord i full storlek:	Ja
Bussprocessor på framsidan:	- MHz
Processorserie:	Intel Core M-5Y Mobile series
Intel® FDI-teknik:	Ja
Intel® Fast Memory Access:	Ja
Intel® Smart Cache:	Ja
Intel® Small Business Advantage (SBA)-version:	1.00
Scenario Design Power (SDP):	3.5 W
Antal Micro HDMI-portar:	1
Power högtalare:	3 W
Främre kameraupplösning:	1280 x 720 Pixels
Maximalt internminne (64-bitars):	8 GB
Wifi:	Ja
Typ produkt:	Hybride (2-in-1)
Batteriteknik:	Lithium-Polymeer (LiPo)
Antal battericeller:	4
Processorgenerering:	Vijfde generatie Intel® Core™ M
Batterijcapaciteit:	34 Wh