Elektrobock Pocket Home PH-SP1 Bruksanvisning
Elektrobock
mottagare
Pocket Home PH-SP1
Läs gratis den bruksanvisning för Elektrobock Pocket Home PH-SP1 (4 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 6.5 recensioner. Har du en fråga om Elektrobock Pocket Home PH-SP1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
Version 11.02
Wireless receiver for control of
electric heating devices
- UNDER THE SWITCH -
PH-SP1
Operating instructions
Control of electric heating systems
Component of the PocketHome®system
Two-way radio communication at 433,92 MHz
The connected electric appliance is switched
according to the required temperature
The control unit PH-BSP is the pilot component
INSTALLATION
The device can only be installed by a person with adequate
qualification! The installation must be executed in
a voltage-free state!
Wiring diagram:
230 V/ 50 Hz
L
N
max.
16 A
L N
FUNCTION BUTTON ( R ) :
SHORT PRESSING (for
about1,5s) -coding.
LONG PRESSING (for about 5s)
-RESET deleting the code from
the memory (the green and red
LEDs flash simultaneously).
PH-SP1 is used for switching the heating device in connection
with the PH-BSP control unit. The big advantage is mounted
directly into the
installation box.
1. Switch off the main circuit breaker.
2. Connect the receiver acc. to the diagram.
3. Switch on the main circuit breaker; the green diode
flashes on the receiver; thus the receiver is ready for
further setting.
4. Shortly press the FUNCTION BUTTON for about
1.5 s (the green and red diode are flashing alternately).
5. On the PH-BSP control unit, press the “Test” button in
the mode to activate the SP ACTIV
switching components (see page 10
of the PH-BSP instructions).
6. If the code has been learned correctly,
the green and red diodes flash
simultaneously.
LED 2LED 1
empty memory, code not learned
code learned
FLASHING ALTERNATELY= code learning mode
FLASHING SIMULTANEOUSLY= code has been learned
SIMULTANEOUS LONG FLASH= code was ERASED
relay switched
ERROR (if no signal is received from the transmitter
within approx. 6 hours, it switches to the 2-min-ON /
8-min-OFF mode). LED flashes only if the relay is on,
i.e. for 2 minutes.
EXPLANATION: LIT UNLIT FLASHING
FUNCTION
ACTIVATION PROCEDURE
INDICATION DIODES
Produktspecifikationer
| Varumärke: | Elektrobock |
| Kategori: | mottagare |
| Modell: | Pocket Home PH-SP1 |
Behöver du hjälp?
Om du behöver hjälp med Elektrobock Pocket Home PH-SP1 ställ en fråga nedan och andra användare kommer att svara dig
mottagare Elektrobock Manualer
31 December 2025
4 September 2024
27 Augusti 2024
26 Augusti 2024
24 Augusti 2024
24 Augusti 2024
19 Augusti 2024
9 Augusti 2024
mottagare Manualer
- Line 6
- Kemo
- Xoro
- Eventide
- Nexa
- Silvercrest
- AMX
- Zoom
- American Audio
- Reely
- Cerwin-Vega
- Madison
- C2G
- Optoma
- Xsarius
Nyaste mottagare Manualer
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025