Eltako FMZ14 Bruksanvisning


Läs gratis den bruksanvisning för Eltako FMZ14 (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 22 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 11.5 recensioner. Har du en fråga om Eltako FMZ14 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/4
Multifunction time relay with 10 functions,
1 CO contact potential free 10A/250V AC,
incandescent lamps 2000 watts*, with
DX technology. Bidirectional. Only 0.4 watt
standby loss.
Modular device for DIN-EN 60715 TH35
rail mounting.
1 module = 18mm wide, 58mm deep.
Connection to the Eltako-RS485 bus. Bus
cross wiring and power supply with jumper.
Wireless window contacts (FTK) and
window handles at opened
windows with
the function NO or NC can be taught-in.
Several FTK and (or) window handles
are linked to each other. If a direction
switch is taught-in, a function (e.g. TI)
can be started using the top switch
(START) and stopped with the bottom
switch (STOP).
Patented Eltako Duplex technology allows
you to switch normally potential free
contacts in zero passage switching when
230V A/C voltage 50Hz is switched.
This drastically reduces wear. To achieve
this, simply connect the N conductor to
the terminal (N) and L to K(L). This
results in an additional standby
consumption of only 0.1 watt.
If supply voltage fails, the two contacts
switch off. When power is restored,
contact 1 closes.
Ti tti b t 0 5 d d
GB
Only skilled electricians may install
this electrical equipment otherwise
there is the risk of fire or electric
shock!
Temperature at mounting location:
-20°C up to +50°C.
Storage temperature: -25°C up to +70°C.
Relative humidity:
annual average value <75%.
RS485 bus actuator
Multifunction time relay
F M Z14
30 014 009 - 2
valid for devices from production week
40/17 (see bottom side of housing)
Typical connection
contact 1 closes.
Time setting between 0.5 second and
20 hours.
Function rotary switches
Teach-in takes place using the top and
middle rotary switches and then the time
is set. T is the time base and xT the
multiplier.
The function is selected using the bottom
rotary switch:
RV = off delay
AV = operate delay
TI =
clock generator starting with impulse
TP = clock generator starting with pause
IA = impulse controlled operate delay
(e.g. automatic door opener)
EW = fleeting NO contact
AW = fleeting NC contact
ARV= operate and release delay
ON = Permanent ON
OFF= Permanent OFF
The LED below the upper function rotary
switch performs during the teach-in
process
according to the operation man-
ual.
It shows control commands by short
flickering during operation.
* The maximum load can be used
starting at a delay time or clock cycle
of 5 minutes. The maximum load will
be reduced for shorter times as follows:
up to 2 seconds 15%, up to 2 minutes
30%, up to 5 minutes 60%.
Typical connection
Description of functions
t1 t2 t1 t2
TI
Wireless
input
K(L)-2
t
t
ARV
Wireless
input
K(L)-2
t1 t2 = 3s
IA
Wireless
input
K(L)-2
t
EW
Wireless
input
K(L)-2
Wireless
input
K(L)-2
AW
t
t1 t2 t1
TP
Wireless
input
K(L)-2
t
AV
Wireless
input
K(L)-2
Wireless
input
K(L)-2
t
RV
Teaching-in wireless sensors in wire-
less actuators
All sensors must be taught-in in the
actuators so that they can detect and
execute commands.


Produktspecifikationer

Varumärke: Eltako
Kategori: Inte kategoriserad
Modell: FMZ14

Behöver du hjälp?

Om du behöver hjälp med Eltako FMZ14 ställ en fråga nedan och andra användare kommer att svara dig