EverFocus EN7517HDM Bruksanvisning
Läs gratis den bruksanvisning för EverFocus EN7517HDM (3 sidor) i kategorin Övervaka. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 6.5 recensioner. Har du en fråga om EverFocus EN7517HDM eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
Installation Guide
Table of Content:
1. Accessories
Please check the following included accessories before installation:
AC cable
one pcs
Monitor Base
o ne pcs
Remote Control
one pcs
Installation Guide
one pcs
2. Installation
Rear Interface Side Interface
3. Connecting the Monitor
Cables to Your Video Source
Make all cable connections are secure
by tightening the cable screws. Shaking
and vibration may dislodge cables that
are improperly connected. Route all
wiring and cabling away from heat
sources, sharp metal edges, and any
sources of electromagnetic and radio
frequency interference.
5. Controls & Functions
Buttons on the Bezelright side of the
If you cannot locate your remote, you can use the side panel buttons of your monitor to operate many of the
monitor’s features.
1. POWER: Turns the monitor on or off.
2. SOURCE: Accesses the available video input signals (AV, BNC, , SVIDEO VGA, HDMI)
3. MENU: Brings up the MONITOR Main menu. When using the OSD (On Screen Display) system, press
MENU button to return to the previous menu or exit.
4. : Up arrow button.
5. : Down arrow button.
6.＋
＋
＋
＋＋ : Increases the volume. In the MONITOR menu system, acts like the right arrow button on the remote
control and adjusts menu controls.
7. :
－
－
－
－－ Decreases the volume. In the MONITOR menu system, acts like the left arrow button on the remote
control and adjusts menu controls.
HOW to use buttons
Use the buttons on the right side control panel to adjust the OSD
(1) Power on the LCD monitor.
(2) Press source button to accesses the available video input signals, press or button to enter the ＋ —
video mode.
(3) Press MENU button then press ＋／－ button move highlight icon left / right.
(4) Press SOURCE button to enter the submenu, then press ＋／－ button corresponding to edit.
(5) When you are satisfied with the setting, press MENU button to return to the previous menu or exit.
1. Accessories
4. Testing the Monitor
7. Mounting Your MONITOR to the Wall
2. Installation
5. Controls & Functions
8. Specification
6. Choose the Input Source
9. Reference
3. Connecting the Monitor
Cables to Your Computer
Pull to open rear cover for BNC and
Audio In/Out as highlighted area.
4. Testing the Monitor
After making all connections secure and tight, turn on the power switch
located on the side bezel.
1. Turn on your computer.
2. Ensure the front LED is green.
3. Make sure the video image is centered within the screen area. Use the
monitor controls to adjust the image, if necessary. Perform an Auto
Config first, then if you wish you can adjust the horizontal and vertical
position, contrast, and brightness to better suit your video card and your
personal preference. Refer to Basic OSD setup for more information on
using the on-screen menu to adjust the video display.
Produktspecifikationer
| Varumärke: | EverFocus |
| Kategori: | Övervaka |
| Modell: | EN7517HDM |
Behöver du hjälp?
Om du behöver hjälp med EverFocus EN7517HDM ställ en fråga nedan och andra användare kommer att svara dig
Övervaka EverFocus Manualer
8 September 2024
6 September 2024
6 September 2024
27 Juli 2024
27 Juli 2024
Övervaka Manualer
- SPL
- Enttec
- Hanwha
- KTC
- Ernitec
- Barco
- Drawmer
- Da-Lite
- Mackie
- Prowise
- Nec
- SEIKI
- GeoVision
- Qian
- DoubleSight
Nyaste Övervaka Manualer
9 April 2025
9 April 2025
8 April 2025
8 April 2025
7 April 2025
5 April 2025
5 April 2025
4 April 2025
4 April 2025
2 April 2025