Extech 380405 Bruksanvisning

Extech Inte kategoriserad 380405

Läs gratis den bruksanvisning för Extech 380405 (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 10 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 5.5 recensioner. Har du en fråga om Extech 380405 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/1

Model 380405- - _V 4 5/ en GB 1. 18

User Manual

Capacitance Decade Box

Model 380405

Introduction

Congratulations on your purchase of the Extech Capacitance Decade Box. This 380405

device oers 5 decades of capacitance ranges from 100pF to 11.111uF (in 100pF steps).

Slide switches allow easy addition and subtraction of capacitance values. Binding posts (3)

oer simp and secure connections. Careful use of this decade box will provide years of le

reliable service.

Specications

Capacitance ranges 100pF to 11.111uF in 100pF steps

Internal Residual Cap 50pF maximum :

Voltage limit 50VDC ( -polarized capacitors) non

Connection Three (3) binding posts

Accuracy 5% (< =1uF: 1kHz test frequency; > 1uF: 100Hz test frequency)

Operating conditions Temperature: 0 to 50oC (32 to 122oF) / Humidity: < 80%RH

Dimensions/Weight 7 x 11.7 x 3.3 (5.79 x 4.61 x 1.3") Approx. 312g (0.69 lbs) 14. cm /

Operation

Binding Post Connections

The binding posts can be used for connections in several ways:

1. A banana plug can be inserted directly into the posts.

2. Bare wire can be threaded through the post after it has been unscrewed. Once the bare wire is threaded, tighten the posts as necessary.

3. Alligator clips can be used but use caution not to strip the post threads or plastic post housing.

The Capacitance output is available on the RED and the BLACK binding posts. The WHITE post is case ground and is typically not used. Connect the

positive lead of the device under test to the RED post. Connect the negative lead to the BLACK post. Use the WHITE grounding post only if the device

under test will be grounded to the 380405 case.

Range Selection

The front panel switches are used to select the capacitance that will be output on the RED and BLACK terminals. When a switch is set to the IN 20

position, the value printed above the switch is added to the total capacitance available at the posts. When the switch is set to OUT it is excluded from

the total capacitance. If all of the switches are set to OUT, the total output capacitance will be zero (+ 50pF residual capacitance ). –approx

For example, if the desired output value is 10.5uF, set the following switches to the IN position: 4uF, 3uF, 2uF, 1uF, 0.4uF, and 0.1uF.

Testing

This device can be used to verify the calibration integrity of multimeters, LCR meters, calibrators, etc. Connect as described in the Binding Post

Connections section above, and then set the capacitance switches to output the desired capacitance. Ensure that the voltage supplied by the device

under test is not greater than 50VDC. The device under test should read the value of capacitance selected on the tester. If it does not, the device

under test may need calibration, adjustment, or repair.

ISO-9001 Certified

www.extech.com

Produktspecifikationer

Varumärke:	Extech
Kategori:	Inte kategoriserad
Modell:	380405
Färg på produkten:	Zwart
Vikt:	11 g
Bredd:	37 mm
Djup:	33 mm
Höjd:	13 mm
Snäll:	Cadanssensorband
Antal per paket:	1 stuk(s)
Ytfärg:	Monochromatisch