Extech CO30 Bruksanvisning

Extech Mätutrustning CO30

Läs gratis den bruksanvisning för Extech CO30 (7 sidor) i kategorin Mätutrustning. Guiden har ansetts hjälpsam av 5 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 3 recensioner. Har du en fråga om Extech CO30 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/7



USER MANUAL



DigitalCOMonitor

ModelCO30



Additional ManualUser Translationsavailable at www.extech.com

EXTECHINSTRUMENTS

 2 CO30‐ ‐en GB_v1.7 11/16

Introduction



Thank you for Model TheselectingtheExtechInstruments  CO30.  CO30is in  ‐a 3 ‐oneCarbon

Monoxide(CO),temperaturemeasurement,andhumiditymeasurement meter.  Thisdeviceis

shipped testedfully  and and,calibrated  withproperuse,willprovideyearsofreliableservice.

Pleasevisit (www.extech.com)our website tocheckforthelatestversionofthisUserGuide,

ProductUpdates, Customerand Support.

Description

MeterDescription

1. Compensationadjustment



2. Controlbutton



3. ACAdaptorjack



4. LCD Display



5. LEDindicator



Note:TiltStand, rearWall access,mount andbatterycompartmentlocatedon ofmeter.



IMPORTANTSAFETY NOTES

The forCO30Carbon Monoxide Monitorisintended general purpose Air Quality monitoring

only,and has any notbeencertifiedforusepursuantto  state orcitysafetyCarbon Monoxide 

AlarmorMonitoringrequirements.

TheCO30Carbon Monoxide Monitorhasnotbeentested anby independentlabto withcomply 

UL    ‐ 2034 or IAS 6 96 standard.

Itisthe theresponsibility of   customertoobtainand andapply current  local,state,  national

regulationswith regard toCO alarms, monitoringandtesting.

EXTECHINSTRUMENTS

 3 CO30‐ ‐en GB_v1.7 11/16

Operation



Poweringthemeter

Ifthe the themeterissuppliedwithoutbatteriesinstalled,install suppliedbatteriesin rear

batterycompartmenttopowerthemeter.Pleaseobserve proper polarity.

Ifthe themeterissuppliedwith batteriesinstalled,and a protectivebatterystripis ininstalled 

the compartment, the thebattery remove protectivestriptopower meter.

Alternatively,plugthe the theACadaptorinto jackon sideofthemeterandthenintoanAC

power powersourceto themeter.

NormalOperationMode

Whenswitched displaysON,the LCD  ‘0000’for that a periodof ontime,depending thetime the

meter thenhasbeeninactive.Themeterwill proceed normaltothe modeofoperationwhere

the LCD the displays currentCOlevelsinppm,theTemperature(°C/°F),andRH%(relative

humidity)alternatelyevery 6 seconds.

Status Indicator LED

The statusFrontpanel LEDuses user a color‐codingsystemtoinformthe astothemeasuredCO

concentration; CautionGreenfor forGood(<10ppm);Yellow  (10to29ppm);RedforDanger

(>30ppm). LEDIfthe failstoilluminate,pleasereturntheunitforservice.

Controlbutton

TheControlbutton meterlocatedon left ofthe side the isusedtocontroland program  a variety

ofmeterfunctions.Pressandholdthe theControlbuttonforatleast 3 secondstoaccess 

Control ControlSetupMode.Repeatedpressesofthe  button availablecyclethroughthe 

parameters.Theseparameters,inorder,are:

 ZERO Calibration

 Temperature   Unit selection (°C/°F)

 Temperature       compensation (used in conjunction with side potentiometer)

 Humidity       compensation (used in conjunction with side potentiometer)

 Alarm         Beeper Threshold (25, 30, 35, 50, 100, 200 ppm)

 Factory   Default setting reset

 Escape/Return(abortandreturntonormalmode)



ZEROCalibration

EnsurethattheZero Calibration is inperformed  a cleanairenvironment(noCOgases).

PressandholdtheControlbuttonfor 3 seconds(until       appears on the LCD screen) and

then enterpressandholdtheControlbuttonagainto thecalibrationmode(‘CAL’should

appearonthedisplay).

Produktspecifikationer

Varumärke:	Extech
Kategori:	Mätutrustning
Modell:	CO30

Behöver du hjälp?

Om du behöver hjälp med Extech CO30 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Mätutrustning Extech Manualer

Extech 44550 Bruksanvisning

18 Mars 2025

Extech CO15 Bruksanvisning

31 Januari 2025

Extech 380941 Bruksanvisning

23 Oktober 2024

Extech 380926 Bruksanvisning

23 Oktober 2024

Extech PRC20 Bruksanvisning

25 September 2024

Extech PRC30 Bruksanvisning

25 September 2024

Extech SD900 Bruksanvisning

25 September 2024

Extech PRC15 Bruksanvisning

25 September 2024

Extech 412300A Bruksanvisning

25 September 2024

Extech 412400 Bruksanvisning

25 September 2024

Mätutrustning Manualer

Nyaste Mätutrustning Manualer

Uni-T UT220 Bruksanvisning

3 April 2025

Uni-T UT681C Bruksanvisning

3 April 2025

Uni-T UT216C Bruksanvisning

3 April 2025

Uni-T UT611 Bruksanvisning

3 April 2025

Uni-T UT210D Bruksanvisning

3 April 2025

Uni-T UT210C Bruksanvisning

3 April 2025

Uni-T UT210B Bruksanvisning

3 April 2025

Uni-T UT682 Bruksanvisning

3 April 2025

Uni-T UT275 Bruksanvisning

3 April 2025

Uni-T UT08A Bruksanvisning

3 April 2025