Extech IR200 Bruksanvisning
Extech
Multimeter
IR200
Läs gratis den bruksanvisning för Extech IR200 (7 sidor) i kategorin Multimeter. Guiden har ansetts hjälpsam av 7 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 4 recensioner. Har du en fråga om Extech IR200 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/7
User Manual
InfraRed Thermometer
with Laser Pointer
MODEL IR400
Additional User Manual translations available at www.extech.com
IR400 en 2.0- - vUS_ 7/22
2
Introduction
Congratulations on your purchase of the Model IR400 IR Thermometer. The IR400 is capable of
non-contact (infrared) temperature measurements at the touch of a button. The built-in laser pointer
increases target accuracy while the backlit LCD and handy pushbuttons combine for convenient,
ergonomic operation. This meter is shipped fully tested and calibrated and, with proper use, will
provide years of reliable service.
Safety
• Use extreme caution when the laser beam is onpointer
• Do not point the beam toward anyone's eye or allow the beam
to strike the eye from a reflective surface
• Do not use the laser near explosive gases or in other
potentially explosive areas
Meter Description
Meter Description
1. Laser pointer beam
2. IR Sensor
3. Measurement Trigger
4. Battery Compartment
5. LCD Display
6. Pushbuttons
7. Handle Grip
Display Description
1. Temperature scan in progress (trigger held)
2. Last reading held (trigger released)
3. Laser pointer ON
4. Emissivity (0.95 fixed)
5. Max or MIN value displayed
6. Temperature display
7. Low battery icon (replace battery)
8. Temperature units
IR400 en 2.0- - vUS_ 7/22
3
Operating Instructions
Basic IR Measurements
1. Hold the meter by its handle and point it toward the surface to be measured.
2. Pull and hold the trigger to turn the meter on and begin testing. The temperature reading, the
flashi and ng ‘SCAN’ icon the unit of measure, , € = 0.95 will appear.
3. seconds Release the Trigger and the reading will hold for approximately 10 (HOLD will appear
on the LCD) after which the meter will automatically shut off.
Laser Pointer
1. When the trigger is pressed, the laser pointer will turn on and identify the spot being measured.
The icon on the display indicates that the pointer is on.
2. To turn the laser pointer off, press the button while scanning. Press the button again to
turn the pointer back on.
MAX - MIN
The Max / Min feature provides a means to display the highest (MAX) or lowest (MIN) temperature
measured during a scan.
1. While the trigger is pressed, press the MAX/MIN button will appear. The “MAX” icon and the
maximum measured temperature will appear in the display. The displayed temperature will not
change until a higher temperature is measured.
2. Press the MAX/MIN button again and the “ ” icon will appear. MIN The minimum temperature
only be displayewill d
3. Press the MAX/MIN button again to return to a real time display.
Temperature Units C/F
To change the temperature units, press and release the trigger. Momentarily press the C/F button
and the temperature unit will change.
Backlight
When the meter is on, press the backlight button to turn the backlight on. Press the button again
to turn the backlight off.
Note: Constant use of the backlight feature will reduce battery life.
Over-Range Indication
If the temperature measurement exceeds the specified temperature range, the thermometer will
display “HI” or “LO” in place of a temperature reading.
Produktspecifikationer
| Varumärke: | Extech |
| Kategori: | Multimeter |
| Modell: | IR200 |
Behöver du hjälp?
Om du behöver hjälp med Extech IR200 ställ en fråga nedan och andra användare kommer att svara dig
Multimeter Extech Manualer
23 December 2024
19 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
11 September 2024
6 September 2024
3 September 2024
2 September 2024
Multimeter Manualer
- Bearware
- Vimar
- PCE Instruments
- Velleman
- CEM
- Altai
- MBS
- EMOS
- Parkside
- REV
- Metrel
- Tacklife
- Heylo
- Brennenstuhl
- Weidmüller
Nyaste Multimeter Manualer
17 Juli 2025
16 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
11 Juli 2025