Extron USB Plus Matrix Controller Bruksanvisning
Extron
Inte kategoriserad
USB Plus Matrix Controller
Läs gratis den bruksanvisning för Extron USB Plus Matrix Controller (12 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 18 personer och har ett genomsnittsbetyg på 3.8 stjärnor baserat på 9.5 recensioner. Har du en fråga om Extron USB Plus Matrix Controller eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/12
1
USB Plus Matrix Controller • Setup Guide
The Extron® USB Plus Matrix Controller is a pre-congured controller that can easily be setup and deployed to control Extron
USBExtenderPlus products in a USB Matrix switching application within a gigabit Ethernet network. Quick and easy setup of
the USBPlusMatrixController, USB Extender Plus transmitters and receivers is done using Extron Product Conguration Soft-
ware (PCS). An Extron Control System or any third party control can interface with the USB Plus Matrix Controller via Ethernet or
RS-232 to perform USB switching.
The main components in a USB Extender Plus Matrix system:
• USB Plus Matrix Controller — The controller is pre-congured to control the USB Extender Plus transmitters and receivers
in a USB Matrix switching application. The default Telnet port is 22123 (see the USB Plus Matrix Controller Help File for full
details).
• USB Plus Extenders (transmitters and receivers) — At least 1 transmitter and 1 receiver are required, and up to 64
extenders total may be included. Each extender must be assigned a unique IP address (DHCP cannot be used to assign
these addresses), and these addresses are uploaded to the USB Plus Matrix Controller. All twisted pair models are supported:
rack mountable models (standard and HID-only), AAP™ models, and decorator-style models (see the USB Extender Plus
Series User Guide, available on www.extron.com, for more information about these models).
• Product Configuration Software (PCS) — This free software is loaded on the computer and is used to congure the
USB Extender Plus transmitters and receivers. It is also used to create a conguration that is uploaded to the USB Matrix
Controller (see the USB Plus Matrix Controller Help File for details on how to use PCS with the USB Matrix Controller).
• Extron Toolbelt — This free software is used to congure the IP settings of the USB Matrix Controller (see the Toolbelt Help
File at www.extron.com for details on how to use Toolbelt).
Installation
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
• Do not perform a Mode 5 reset (see USB Plus Matrix Controller Help File) to the USB Matrix Controller. Doing so will
erase the factory loaded conguration used to control the USB Extender Plus transmitters and receivers.
• N’effectuez aucune réinitialisation complète de système (mode 5) (voir USB Plus Matrix Controller Help File) sur l’USB
Matrix Controller. Cette action entraînera en effet la suppression de la conguration par défaut, utilisée pour le contrôle
des émetteurs et récepteurs USBExtenderPlus.
The following diagram shows an example of a USB Plus Matrix Controller system setup:
USB EXTENDER Plus R
CONFIG
PAIR
STATUS
LINK
HOST
1
3
2
4
Rx 1
USB EXTENDER Plus R
CONFIG
PAIR
STATUS
LINK
HOST
1
3
2
4
Rx 2
USB EXTENDER Plus R
CONFIG
PAIR
STATUS
LINK
HOST
1
3
2
4
Rx 3
USB EXTENDER Plus R
CONFIG
PAIR
STATUS
LINK
HOST
1
3
2
4
Rx 4
LAN
Tx
1
USB EXTENDER Plus T
STATUS
LINK
HOST
CONFIG
PAIR
Tx
2
USB EXTENDER Plus T
STATUS
LINK
HOST
CONFIG
PAIR
Tx
3
USB EXTENDER Plus T
STATUS
LINK
HOST
CONFIG
PAIR
Tx
4
USB EXTENDER Plus T
STATUS
LINK
HOST
CONFIG
PAIR
USB Matrix Controller
Control System
SIS (Simple Instruction Set Commands)
a
t
COM
RTS
CTS
Tx
Rx
R
USB PLUS MATRIX
C
C
o
t
n
t
ro
l
l
S
S
y
t
s
t
em
t
r
t
rix
C
ontrolle
r
S
I
S
(S
im
p
le Ins
t
Control
Figure 1. Application Diagram of the USB Plus Matrix Controller System
1
Produktspecifikationer
| Varumärke: | Extron |
| Kategori: | Inte kategoriserad |
| Modell: | USB Plus Matrix Controller |
Behöver du hjälp?
Om du behöver hjälp med Extron USB Plus Matrix Controller ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Extron Manualer
2 April 2025
2 April 2025
2 April 2025
2 April 2025
12 Mars 2025
10 Mars 2025
25 Februari 2025
25 Februari 2025
25 Februari 2025
25 Februari 2025
Inte kategoriserad Manualer
- Ordex
- BYD
- Pinolino
- JIMMY
- BERTSCHAT
- Drawmer
- Schoeps
- AmerBox
- Soundcraft
- Akasa
- AudioThing
- Platinum
- Maclean
- Dormakaba
- Proline
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025