Extron UTS 100 Bruksanvisning
Extron
Inte kategoriserad
UTS 100
Läs gratis den bruksanvisning för Extron UTS 100 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 3.7 stjärnor baserat på 10.5 recensioner. Har du en fråga om Extron UTS 100 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
UTS 100 (70-1028-01)
(8) #4-40 x 3/16 inch product mounting screw
(4) #8 x 1/2 inch shelf mounting screw
UTS 150 (70-1028-02)
(8) #4-40 x 3/16 inch product mounting screw
(2) #8-32 Thumbnut
Step 1 — Mount Devices on the Shelf
ATTENTION: Some products have hexagonal holes
in their base, which anchor stand-offs for internal circuit
boards (see the gure to the right). Using these holes will
damage the product and will not provide secure mounting.
Before securing a device to the shelf, decide where the device
will be placed. Ensure that adequate space remains for running
cables.
1. Place the device on the shelf so that the rack mounting
holes are aligned with two diagonally opposite product
mounting holes in the shelf (see gure at right).
Remove any rubber feet attached to the device.
2. Secure the device to the shelf, using two
of the provided #4-40 x 3/16 inch
screws.
3. Use the rectangular (wire tie)
openings for tie wraps if
necessary.
UTS 100 Series • Setup Guide
The Extron UTS100 and UTS 150 under-table shelf system accommodates half-rack,
quarter-rack, and eighth-rack products in a half-rack width installation. The shelves can
accommodate a single device or combinations of smaller devices.
Included Parts
Step 2 — Install the UTS 100 (Primary Shelf) Under the Table
The UTS 100 may be mounted under furniture in
one of two ways: using the keyhole slots for
a removable installation or the clearance
holes for a fixed installation.
1. Hold the UTS 100 under
the desk or table and mark
the locations of four corner
mounting holes.
Clearance
hole
Keyhole
slot
#4-40 Thread for
Rack Mounting
Hexagonal
Stand-off (for
mounting circuit
board)
Use 2 mounting holes on diagonally
opposite corners of device.
(2) #4-40 x 3/16"
screws
UTS 100
Wire tie
openings
Product
mounting
holes
Produktspecifikationer
| Varumärke: | Extron |
| Kategori: | Inte kategoriserad |
| Modell: | UTS 100 |
Behöver du hjälp?
Om du behöver hjälp med Extron UTS 100 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Extron Manualer
2 April 2025
2 April 2025
2 April 2025
2 April 2025
12 Mars 2025
10 Mars 2025
25 Februari 2025
25 Februari 2025
25 Februari 2025
25 Februari 2025
Inte kategoriserad Manualer
- Overtone Labs
- Tormatic
- Benning
- Commercial Chef
- CLIMAQUA
- AVPro Edge
- Husky
- Vasagle
- Tornado
- Anthro
- AudioThing
- Armcross
- Blizzard
- SKLZ
- City Theatrical
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025