Fisher And Paykel E522BRXFDUQ4 Bruksanvisning

Fisher And Paykel kylskåp E522BRXFDUQ4

Läs nedan 📖 manual på svenska för Fisher And Paykel E522BRXFDUQ4 (60 sidor) i kategorin kylskåp. Denna guide var användbar för 11 personer och betygsatt med 4.9 stjärnor i genomsnitt av 6 användare

Ladda ner PDF

Sida 1/60

NZ AU GB IE EU AE HK SG

ActiveSmart™ refrigerator

Ice & Water and Non-Ice & Water

E372B, E402B, E406B, E442B,

E522B, RF522W, RF522A,

RF610A & RF540A models

Installation instructions

and User guide

Important!

It is important that this User Guide is retained with your refrigerator for future reference.

Should the appliance be sold or transferred to another owner, please ensure that the

User Guide is left with the appliance. This will ensure that the new owner can familiarise

themselves with the information and warnings contained within the Guide.

Contents

Important!

SAVE THESE INSTRUCTIONS

The models shown in this User Guide may not be available in all markets and are subject to change at any time.

For current details about model and specification availability in your country, please visit our website listed on

the back cover or contact your local Fisher & Paykel dealer. Note that the word “refrigerator”, throughout this

User Guide, refers to combination refrigerator/freezer products.

Introduction 2

Safety and warnings 3

Installation instructions 7

Moving or storing your appliance 21

Door conversion 22

Soft closing refrigerator door feature 22

ActiveSmart™ operating instructions 23

All about the external display (Ice & Water models only) 27

Using your water dispenser (Ice & Water models only) 28

Water filter (Ice & Water models only) 29

Using your ice maker (Ice & Water models only) 31

ActiveSmart™ special features (all models) 33

Cleaning and caring for your refrigerator 36

Storing food in your refrigerator 40

Storing food in your freezer 42

ActiveSmart™ user warnings and sounds 44

Troubleshooting 45

Manufacturer’s Warranty 49

Customer Care 51

European directive 2002/96/EC on Waste Electrical and

Electronic Equipment (WEEE) 53

Filter performance data sheet 54

Thank you for buying a Fisher & Paykel ™ refrigerator.ActiveSmart

At Fisher & Paykel we are very proud of this refrigerator. This refrigerator combines size and

storage space with the latest features and functions.

Thousands of hours of food care research and 75 years of refrigeration experience has been

programmed into your refrigerator to give you the best possible performance.

We hope you enjoy your new refrigerator.

Note: non Ice & Water models do not have an external water dispenser.

Fig.1 ActiveSmart™ refrigerators

Refrigerator French door

and freezer drawer

Refrigerator door

and freezer door

Refrigerator door

and freezer drawer

Introduction

WARNING!

Electric Shock Hazard

Read and follow the SAFETY AND WARNINGS outlined

in this User Guide before operating this appliance.

Failure to do so can result in death, electric shock, fire or

injury to persons.

Use this appliance only for its intended purpose as described in

this User Guide.

Important safety precautions

Warning

When using this appliance always exercise basic safety precautions

including the following:

Danger

Refer to the stability bracket and leaflet supplied to avoid hazard

due to instability of the appliance.

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety.

Young children should be supervised to ensure they do not play

with the appliance.

The manufacturer’s installation instructions for product and

cabinetry ventilation must be followed when installing the

appliance.

Keep ventilation openings, in the appliance enclosure or in the

built-in structure, clear of obstruction.

Safety and warnings

Cleaning

Many commercially available cleaning products contain solvents

which may attack plastic components of your refrigerator and

cause them to crack. Please refer to the cleaning care section of this

booklet for further advice.

Electrical

This appliance must be installed in accordance with the installation

instructions before use.

Never unplug your refrigerator by pulling on the power cord.

Always grip the plug firmly and pull straight out from the outlet.

Do not plug in any other appliance at the same power point as your

refrigerator or use extension cords or double adapters.

Repair or replace immediately all electric service cords that have

become frayed or otherwise damaged. Do not use a cord that

shows cracks or abrasion along its length or at either the plug or

appliance end.

If the power supply cord is damaged, it must only be replaced by

your Fisher & Paykel Authorised Repairer because special purpose

tools are required.

When moving your appliance away from the wall, be careful not to

roll over or damage the power cord.

Do not use electrical appliances inside the food storage

compartments of the appliance.

Important!

Your refrigerator is designed to operate for many years without

the need for service checks. However, if your refrigerator is

malfunctioning, have it attended to by your Fisher & Paykel

Authorised Repairer as soon as possible. All electrical repairs must

be carried out by an adequately trained service technician or

qualified electrician.

Safety and warnings

Storing food and drinks

DO NOT store explosive substances such as aerosol cans with a

flammable propellant in this appliance.

Never store volatile or flammable materials in your refrigerator as

they may explode.

Never freeze liquids in glass containers. Liquid expands during

freezing, which may cause the container to explode.

Never freeze carbonated drinks. They may explode.

Do not consume food if it is too cold. Food removed from the

freezer compartment may be cold enough to cause damage when

brought into contact with bare skin, eg frozen ice cubes.

Power failure – food safety

Do not refreeze frozen foods that have thawed completely. Follow

the recommendations below if you discover food in your freezer

has thawed:

1) Ice crystals still visible – food may be refrozen but should be

stored for a shorter period than recommended.

2) Thawed but refrigerator cold – refreezing generally not

recommended. Fruits and some cooked food can be refrozen but

use as soon as possible. Meat, fish, poultry – use immediately or

cook then refreeze. Vegetables – discard as they usually go limp

and soggy.

3) Thawed and warmer than 5°C (41°F) – discard all food.

Do not refreeze frozen foods that have thawed completely. The

food may be dangerous to eat.

SAVE THESE INSTRUCTIONS

Installation instructions

Please follow the installation steps below to ensure your appliance operates correctly.

1. Power

The appliance must be installed so the plug is accessible.

To ensure that the appliance is not accidentally switched off, connect your refrigerator to its

own power point. Do not plug in any other appliance at this power point or use extension cords

and double adaptors, as the combined weight of both power cords can pull the double adaptor

from a wall outlet socket.

For power requirements, refer to the information on the serial plate located at the front bottom

right-hand side of the refrigerator when the door is open.

It is essential that the appliance is properly grounded (earthed).

2. Location

Your refrigerator should not be located in direct sunlight or next to any heat generating

appliance such as a cooktop, oven or dishwasher.

3. Ice & Water (Ice & Water models only)

Your Ice & Water refrigerator must be installed by an authorised plumber or Fisher & Paykel

Authorised Repairer as incorrect plumbing can lead to water leaks.

Fisher & Paykel Appliances does not accept responsibility for damage (including water damage)

caused by faulty installation or plumbing.

Installation instructions

4. Ventilation and installation – Freezer door models

(E372B, E402B, E406B, E442B, E522B) (Ice & Water and non Ice & Water)

For all products with a freezer ‘door’ refer to page 8 – 9 for installation instructions. For all

products with a freezer ‘drawer’ (RF522W, RF522A and RF610) refer to pages 10 – 11 for

installation instructions.

To ensure adequate ventilation for your refrigerator or vertical freezer, see recommended

cabinetry dimensions below.

If integrating your refrigerator, follow installation instructions provided with the please

integration kits.

Flush with refrigerator door – 90° door rotation

D A

B C P

Flush with refrigerator chassis – full door rotation

P M M

Flush with refrigerator door – full door rotation

H/I

P M N

P M

K/L

Note: these drawings and dimensions are also true for Ice & Water models.

Installation instructions

Product dimensions (mm) E372B E402B E406B E442B E522B

overall height of flat door product n/a 1715 n/a 1715 1715

overall height of curved door product 1595 1695 1595 1695 1695

overall height of curved door

with ice & water product n/a n/a n/a n/a 1705

overall width of product 635 635 680 680 790

overall depth of flat door product

(excludes handle, includes evaporator) n/a 695 n/a 695 695

overall depth of curved door product

(excludes handle, includes evaporator) 715 715 715 715 715

Cabinetry dimensions (mm) (including minimum clearances)

inside height of cavity 1645 1735 1645 1735 1735

Flush with refrigerator chassis – full door rotation

inside width 675 675 720 720 830

inside depth 620 620 620 620 620

Flush with refrigerator door – full door rotation

inside width 790 790 835 835 945

inside depth flush to curved door 680 680 680 680 680

inside depth flush to flat door n/a 695 n/a 695 695

Flush with refrigerator door – 90° door rotation

(for full drawer/shelf access, the doors need to be open past 90°)

inside width 745 745 790 790 900

inside depth flush to curved door 680 680 680 680 680

inside depth flush to flat door n/a 695 n/a 695 695

Minimum clearances

side clearance 20 20 20 20 20

side clearance – hinge side

flush with door – full rotation 135 135 135 135 135

side clearance – hinge side

flush with door – 90° rotation 90 90 90 90 90

rear clearance (incl. evaporator tray) 30 30 30 30 30

vent – around top of cupboard (optional) 50 50 50 50 50

top clearance – above refrigerator cabinet 50 50 50 50 50

door clearance – hinge side

flush with chassis – full rotation 520 520 555 555 645

door clearance – hinge side

flush with door – full rotation 405 405 440 440 530

Installation instructions

RF522W

5. Ventilation and installation – Freezer drawer models

(RF522W, RF522A, RF610A/RF540A) (Ice & Water and non Ice & Water)

Flush with refrigerator chassis – full door rotation

Flush with refrigerator door – 90° door rotation

Flush with refrigerator chassis – full door rotation

Flush with refrigerator door – full door rotation

Flush with refrigerator door – 90° door rotation

Flush with refrigerator door – full door rotation

C P

P M M

H/I

P M N

P M

K/L

D A

B C P

P M M

H/I

P N N

K/L

P N O

Note: these drawings and dimensions are also true for Ice & Water models.

RF522A/RF610A/RF540A

Installation instructions

To ensure adequate ventilation for your refrigerator see recommended cabinetry dimensionsbelow.

Product dimensions (mm) RF522W RF522A

RF610/

RF540A

overall height of product 1715 1715 1790

overall width of product 790 790 900

overall depth of product (excludes handle, includes

evaporator) 695 695 695

Cabinetry dimensions (mm) (including minimum air clearances)

inside height of cavity 1735 1735 1810

Flush with refrigerator chassis – full door rotation

inside width 830 830 940

inside depth 620 620 620

Flush with refrigerator door – full door rotation

inside width 945 1060 1170

inside depth flush to curved door – – –

inside depth flush to flat door 695 695 695

Flush with refrigerator door – 90° door rotation

(for full drawer/shelf access, the doors need to be open past 90°)

inside width 900 1015 1125

inside depth flush to curved door – – –

inside depth flush to flat door 695 695 695

Minimum clearances

side clearance 20 20 20

side clearance – hinge side flush with door – full rotation 135 135 135

side clearance – hinge side flush with door – 90° rotation 90 90 90

rear clearance (incl. evaporator tray) 30 30 30

vent – around top of cupboard (optional) 50 50 50

top clearance – above refrigerator cabinet 50 50 50

door clearance – hinge side flush with chassis – full rotation 645 325 365

door clearance – hinge side flush with door – full rotation 530 210 250

Installation instructions

6. Connecting water (Ice & Water models only)

If your product is an Ice & Water model you must follow steps on pages 12 – 17.

Contents of filter kit

4 m (13 ft) white 6 mm (¼”) tubing

1 x 200 mm (8”) blue tubing

1 x pressure reducing valve (PRV)

1 x double sided foam

2 x locking keys

1 x water filter cartridge and head

1 x tap connection – 15 mm (½”) BSP

Fig.2 Water connection kit

1 2 3 4 5 6 7

Important!



The water connection to your Ice & Water refrigerator must be installed by an authorised plumber

or Fisher & Paykel Authorised Repairer.



The water connection instructions below are intended only for the professional installer.



It is imperative the pressure reducing valve (PRV) is fitted upstream of the filter. If the PRV is not

fitted to the connection line, the Ice & Water features may not function in some circumstances.



The new tubings supplied with the refrigerator are to be used. Old tubings should not be used.



Replacement parts are available through Customer Care or online at www.fisherpaykel.com (this

service is available to selected markets only).

Installation instructions

Important!



DO NOT use with water that is microbiologically unsafe or of unknown quality.



WARNING – connect to potable water supply only.



DO NOT install on line pressure above 827 kPa (119 psi) or below 150 kPa (22 psi).



DO NOT use on hot water supply (25°C (77°F) max).



DO NOT cut any length of tube shorter than 200 mm (8”).



DO NOT install near electrical wires or water pipes that will be in the path of drilling when

selecting the location of the filter system.



DO NOT mount the filter in such a position that it will be struck by other items, such as

wastebaskets, etc.



DO NOT install the filter or any water tubing in direct sunlight as prolonged exposure to light can

weaken plastic components.



DO NOT install the filter in a location that is susceptible to freezing temperatures as damage to

the filter housing could occur.



DO NOT screw the filter to the refrigerator.



DO NOT install the filter or any water tubing in high temperature areas eg in a ceiling cavity.



AVOID contamination of pipes during installation.



DO NOT use copper tubing. The plastic tubing supplied should always be used.



DO NOT continuously dispense water for a period longer than 2 minutes.

Installation instructions

Installation instructions:

Ensure the refrigerator is not plugged into a power supply.

Locate isolation tap for water connection – cold water feed

only (dishwasher or sink mixer taps). Tee and tap fitting not

supplied.

Connect the 200 mm (8”) blue tubing to the outlet of the

PRV (blue collet) and the inlet connection of the water filter

cartridge as shown in Diagram 1. Gently pull on both ends

to ensure it is locked.

Connect the white 6 mm (¼”) tubing to the outlet of the

water filter cartridge as shown in Diagram 2. Gently pull to

ensure it is locked.

Measure the required length of tubing to run from the PRV

to the water connection point (no less than 250 mm (10”)).

Cut the tubing making sure the ends are square and clean.

Connect the tubing to the tap connection and the base

of the PRV (white collet) and then to the tap as shown

in Diagram 3. Take care not to over-tighten the tap

connection. Please note that the tap connection supplied

should fit most installation situations.

Connect one locking key to each side of the water filter

cartridge in between the cartridge and the locking collet

as shown in Diagram 4.

To flush the water filter of any trapped air, harmless

carbon fines and to also check for leaks, aim the end of

the tubing into a bucket, turn isolating tap on and run at

least 10 L (10 qt) of water through. Once complete, turn

isolating tap off.

Locate desired position for water filter noting carefully

the following points:



It is recommended to fit the water filter in a vertical

orientation with the water filter head at the top. This

will minimise water leakage when replacing cartridge.



Ensure the filter is in a convenient location to access

every 6 months for replacement. We suggest that

this location is beside the water filter supply tap in a

cupboard beside the refrigerator.



A minimum clearance of 64 mm (2 ½”) from the

bottomof the filter cartridge is required to perform

cartridge removal.



Do not screw the water filter to the refrigerator.

Fig.3 PRV connection

Diagram 1

Diagram 2

Fig.4 Waterline connection

INLET

Diagram 4

Fig.6 Locking key

Diagram 3

Fig.5 Tap connection

Installation instructions

Attach double sided foam to the back of the water filter head as shown in

Diagram 5. Write the date to be replaced on the filter (date installed +6months).

Remove double sided foam backing and attach filter to the desired position as

located in step 10 (refer to previous page).

Run the 6 mm (¼”) tubing to the back of the refrigerator ensuring there is

enough tubing to pull the refrigerator out for service.

Connect tubing into the water (solenoid) valve located on the right hand side of

the unit (compressor) compartment as shown in Diagram 7. Beware of hot pipes.

Pull gently on tubing to ensure it is locked in as shown in Diagram 8.

The completed installation should look like Diagram 9 on page 16.

Fig.8 Waterline connection

to refrigerator

Diagram 7

Diagram 6

Diagram 8

Turn isolating tap on and check that all connections are dry and free of drips.

Coil water line tubing behind the refrigerator. Push the refrigerator into place being careful not

to kink or squash the water line running into the water (solenoid) valve.

Read and follow pages 16 and 17 before using your ice and water system.

Diagram 5

Fig.7 Double sided

foam attachment

Installation instructions

Important!

All connections must be checked for leaks.

Ensure white 6 mm (¼”) tubing is routed away from sharp objects, sharp corners (beware of

kinking tube as this will stop water flow), clear of the refrigerator unit compartment and not in a

location where it can be squashed.

Ensure all push-fit connections are firmly pushed into place. The tube should be pushed in 16 mm

(5/8”) before reaching the stop.

If tubing is removed at any point, re-cut the end and re-insert. Tubing must be fully inserted to

avoid leaks.

To remove tube from connection points, turn off the isolating tap, push in the collet and gently

pull tubing at the same time.

Fig.9 Connection to water supply

Diagram 9

The water filtration system is tested and certified by NSF International against NSF/ANSI

Standard 53 for the reduction of Asbestos, Atrazine, Benzene, Cyst, Carbofuran, Lead, Lindane,

Mercury, P-Dichlorobenzene, Toxaphene & Turbidity; against Standard NSF/ANSI 42 for the

reduction of Chlorine Taste and Odour and Nominal Particulate Class I to a capacity of 2,838

Litres (750 gallons).

Installation instructions

Before you start using your Ice & Water refrigerator

Check your refrigerator is switched on and has cooled for at least 2 hours before use (refer to

page 23 – The temperature of your refrigerator and freezer).

Check that the isolation tap has been connected and turned on.

The first time you use your water dispenser, there will be a 1 – 2 minute delay while the tank

fills until water is dispensed. Run through and discard the first 3 litres (3 qt) of water, stopping

intermittently to remove trapped air in the system. Failure to do this will result in excessive

dripping from your dispenser.

Turn the ice maker on by pressing the button (refer to pg 31). The light above the button

will be illuminated when the ice maker is on.

Press and hold the and buttons together for 4 seconds and then close the ,

refrigerator compartment door to force an ice maker cycle. The ice tray will flip twice. Repeat

to force another ice maker cycle. The ice tray will flip twice and spill water into the ice bin.

Empty the water, dry and replace the bin. Note that the ice tray will not flip until the refrigerator

compartment door is closed.

Please discard the first 3 harvests of ice (8 cubes per harvest).

You are now ready to enjoy ice and water from your ™ refrigerator.ActiveSmart

Fig.10 Water dispenser

Please note that once installation is complete a few drips may appear out of the dispenser over

the next few days as the remaining trapped air is cleared.

Installation instructions

7. Installation (all models)

Your Fisher & Paykel refrigerator ActiveSmart™

is fitted with front and rear rollers, designed

for moving the product in the forwards and

backwards direction.

Avoid moving the product in a sideways direction

as this may damage the rollers or the floor

covering/surface.

Your refrigerator will arrive with the front feet

wound up making moving the product into its

final location a simple task.

Roll the refrigerator into its final position making

sure there is the correct air gap between the product

and surrounding cabinetry. See minimum clearance in

cabinetry dimensions table (refer to page 8).

Adjust the front feet down until the refrigerator is leaning

backward with the front approximately 10 mm (½”) higher

than the back. This will ensure a good door closing action.

(Refer to Fig.11).

(Non French door models only)

Aligning your refrigerator with cabinetry.

Align the sides of the refrigerator with the cabinetry by

adjusting the hinge side front foot.

Adjust the handle side foot until it touches the floor and

takes a small amount of weight.

Once the refrigerator is in place and aligned with

cupboards/alcove gently push on the front top and check

if the product is rocking or stable.

8. Levelling of refrigerator doors

(French door models only)

For uneven surfaces, front feet can be used to align the

2 doors.

If left hand door is too low, then unscrew the left hand

foot to lift up the cabinet until the two doors top edges

are aligned.

If right hand door is too low, then adjust the right hand

foot in the same way (refer to figures 12 and 13).

Fig.13 Even door alignment

Fig.12 Uneven door alignment

Raise the front of

the refrigerator

Lower the front

of the refrigerator

Fig.11 Refrigerator feet

Installation instructions

9. What to do if your product is unstable

Gently push the refrigerator back until the rear rollers

contact the floor.

Measure the gap under the front foot, which has come

off the floor.

Obtain some solid packing material (hardwood,

plastic,etc) which fits firmly into the gap under the foot.

Note: do not use metallic materials that may corrode,

stain and/or damage floor coverings.

Wind both front feet up and roll the product out

ofposition.

Place the packing material in the location diagonally

opposite the front roller that lifts off the floor.

Make sure the packing material stays in place when the

product is pushed back into position.

Ideally, the packing material is large enough to rest

against the back wall so as to prevent it from moving

when the cabinet is pushed into position.

Wall behind refrigerator

For example: if this foot lifts off

the floor when pushing gently on

the top front of the refrigerator

Packing material goes under rear roller

diagonally opposite front foot that lifts

Fig.15 Stabilising your refrigerator

Roll the refrigerator back into position and adjust front feet as per step

. (Check alignment

and door closing action are satisfactory).

Make small adjustments to front feet where necessary.

Check that the product is stable (all 4 feet are on the floor). If not, repeat

and

This foot lifts off the floor when

top front is gently pushed back

Example only

Unlevel floor

Fig 14. Unstable refrigerator

Installation instructions

Before placing food in the fresh food or freezer compartments

Remove all internal packaging. Ensure that all transit clips are removed from the refrigerator.

These are small rubber stoppers located at the back of the shelves.

Clean the inside of the appliance with a mix of warm water and a small amount of liquid

detergent, and a soft cloth to remove manufacturing and transportation dust.

Allow the refrigerator and freezer to run empty for 2 – 3 hours to allow each compartment to

cool to the appropriate temperature.

The appliance may have an odour on its initial operation, but this will go when the refrigerator

and freezer have cooled sufficiently.

Energy efficiency

For the most energy efficient use of your appliance:

Ensure your refrigerator has adequate ventilation as recommended in the installation

instructions.

Do not cover your appliance with any material that will prevent air from flowing around the

cabinet sides.

Allow good clearances in front of air ducts within the cabinet for maximum cold air distribution.

Cool hot foods down before placing them in the appliance.

Do not overfill the compartments.

Keep door openings to a minimum.

Select a temperature setting that isn’t too cold.

Check your door seals for leaks.

Moving or storing your appliance

If your refrigerator is turned off for any reason, wait 10 minutes before turning it back on. This

will allow the refrigeration system pressures to equalise before restarting.

Moving your refrigerator

Turn off the appliance and unplug from the power point. Remove all food.

Turn the adjustable feet to the right as far as they will turn (refer to page 18).

Ease the refrigerator out of its position. Tuck the power cord away, tape the shelves in place and

tape the doors closed. If the cabinet needs to be placed at an angle or laid down, carefully lay it

on its side (the right hand side when viewed from the front).

Relocate and install. If the appliance has been left on its side for any length of time, leave it

standing upright as long as possible (as least a few hours) before turning it on.

Storing your refrigerator

When storing your cleaned appliance, leave the doors open. This allows air to circulate and

prevents the build up of bacteria and moulds.

Before using again, clean well using a mixture of warm water and a small amount of liquid

dishwashing detergent. Rinse with clean water and dry with a soft lint-free cloth.

Holiday time

We recommend you leave your refrigerator operating while you are on holiday.

Door conversion

ActiveSmart™ refrigerator models with silver handles need to be ordered at the point of purchase

either with left or right opening doors and can not be interchanged.

All other models need to have an appropriate conversion kit for that model refrigerator.

The kit is available from your Fisher & Paykel Authorised Repairer or Dealer. Full instructions are

included in the conversion kit.

If you need to hinge your door on the opposite side we recommend that you call your local

Fisher & Paykel Authorised Repairer or Dealer to make this conversion.

This does not apply to French door models.

Soft closing refrigerator door feature (where fitted)

The fresh food compartment of your refrigerator has been fitted with a soft closing door feature.

You do not need to push the door fully closed as this feature will automatically close the door

from a 45° (approximate) opening angle.

All soft close models

You may notice a little more resistance when opening the door(s) to what you are used to.

The closing speed of the door(s) decelerates at the end of closing. This is to prevent the door(s)

from slamming and to ensure your food items are cared for.

The speed of soft closing can depend on:

The load stored in the door shelves.

The temperature of the fresh food compartment.

The ambient temperature.

French door soft close models only

The soft closing feature enables you to shut either the left or right door first.

You may notice that the closing speed of the left hand door is slightly faster than that of the

right hand door. This is perfectly normal.

The freezer drawer is fitted with an additional mechanism to soft close within the last 50 mm.

Important!

Keep hands and food items clear of the door opening when the gap less than 45° (the soft close

activation range).

The soft closing feature is located inside the door cavity therefore it is not serviceable by the user.

If a problem occurs, please contact your Fisher & Paykel Authorised Repairer.

ActiveSmart™ operating instructions

Models: 635mm wide E372B, E402B

680mm wide E406B, E442B

790mm wide E522B, RF522A, RF522W

900mm wide

RF610/RF540A

The control panel enables you to view and modify all the features and options on your refrigerator.

Temperature control (all models)

When the refrigerator is first turned on, the powerful cooling system will automatically cool

both refrigerator and freezer compartments to their set temperatures. This will take between

2–3hours.

The two compartment temperatures are accurately and independently controlled and do not

change with the temperature or humidity of the surroundings; whether summer or winter.

If you wish to alter the temperature of either the fresh food compartment or freezer

compartment, this can be easily done by using the internal control panel located at the front

right of the compartment.refrigerator

Internal control panel to adjust temperatures

Fig.18 Internal control panel

for Ice & Water models

Fig.17 Internal control panel

for Designer and Elegance

models

Fig.16 Internal control panel

for Tasman models

ActiveSmart™ operating instructions

Fresh food compartment (all models)

The fresh food compartment light will be illuminated. The temperature for this automatically

compartment will show as a series of lights.

The temperature may be altered by pressing the or buttons. One press on either of these

buttons will reduce or increase the number of lights by one which indicates a small change in

temperature.

Fewer lights illuminated means a cooler temperature for the compartment selected.

Freezer food compartment (all models)

To adjust the freezer temperature press the button once so the freezer compartment light is

illuminated.

The freezer temperature can be altered by pressing the or buttons.

One press on either of these buttons will reduce or increase the number of lights illuminated

which indicates a small change in temperature.

Fewer lights illuminated means a cooler temperature for the compartment selected.

Note: successively pressing the button will automatically scroll between the compartments.

When the door is re-opened the control panel will return automatically to the fresh food

compartment setting.

Alarm Mute (all models)

For times when you require the door to be open longer than normal eg when cleaning the interior

of your refrigerator press the ALARM MUTE button to silence the door alarm for 20minutes.

To activate, press the button . The ALARM MUTE light will be illuminated when the once

function is activated.

ALARM MUTE will deactivate after 20 minutes and the door alarms will return to normal.

To deactivate ALARM MUTE manually, press the button again. When ALARM MUTE is

deactivated the light is off.

Note: when the fresh food or freezer compartment door is left open for long periods of time food

quality and / or safety may be compromised.

Door alarms (all models)

If the fresh food compartment door is left open the alarm will beep after 90 seconds and if the

freezer door is left open the alarm will beep after 60 seconds.

While either door remains open, subsequent beeps will sound every 30 seconds for 5 minutes.

A continuous alarm will sound if either of the doors have been left open for 5 minutes or longer

and the interior compartment will turn off. The alarm will stop when the door(s) is light(s) only

closed.

Note: if ALARM MUTE has been activated the door alarms will be silenced for 20minutes. After

5 minutes of the doors being left open the compartment light will turn off however the normal

door alarms will be suspended. The ALARM MUTE light will be illuminated to indicate that the

appliance is in this mode.

ActiveSmart™ operating instructions

Key Mute (all models)

KEY MUTE allows you to silence all button presses.

To activate KEY MUTE and silence buttons, press and hold the button for 4 seconds.

The icon on the internal control panel will be illuminated.

The keys will be silenced when KEY MUTE is activated.

Door alarms and BOTTLE CHILL alarm will still operate.

KEY MUTE will not automatically deactivate. To manually deactivate, press and hold the

button for 4seconds.

The icon will no longer be illuminated.

Key Lock (all models)

KEY LOCK allows you to disable the buttons on the internal control panel. This is useful when

cleaning your refrigerator.

To activate KEY LOCK press and hold the and buttons for 4seconds.

The icon on the internal control panel will be illuminated.

Pressing any of the buttons will cause a raspberry beep to tell you that they are disabled.

KEY LOCK will not automatically deactivate. To manually deactivate, press and hold the

and buttons for 4 seconds.

The icon will no longer be illuminated.

Sabbath mode activation (all models)

To activate SABBATH MODE, open the door(s) of the fresh food compartment and freezer

compartment and then press and hold the and buttons on the internal control

panel for 4seconds.

The candle icon will illuminate when SABBATH MODE has been activated.

When the product is in Sabbath mode:

The icon on the internal control panel will be illuminated.

All lights on the internal control panel except for the candle icon will be off.

The fresh food or freezer compartment lights will operate when the door(s) is opened.not

The door alarms will not operate.

The internal control panel will not function except to indicate SABBATH MODE is active as

stated above.

Opening the door(s) will not affect the compressor or fans.

If the power to the refrigerator is turned off whilst in this mode, the product will continue in

SABBATH MODE when the power is restored.

SABBATH MODE will automatically de-activate 80 hours after activation.

To de-activate earlier than 80 hours press and hold the and buttons for 4seconds.

The candle icon will no longer illuminate on the internal control panel and functionality of the

internal control panel will return to normal.

ActiveSmart™ operating instructions

Special Functions

Bottle Chill (Elegance, Designer and Ice & Water models only)

This function allows you to chill your beverages more rapidly in the freezer without the worry of

forgetting about them. The timer is set for 15 minutes however the time taken to chill depends

on the size of your beverage. If after 15minutes your beverage is not cold enough, simply place

it back in the freezer and reset the BOTTLE CHILL function.

To activate, press the button on the internal control panel. The BOTTLE CHILL light will be

illuminated when the function isactivated. The icon will be illuminated on the external display

(Ice & Water models only).

An alarm will sound after the 15 minute time has elapsed.

For non Ice & Water models: open the fresh food compartment door and press the button

on the internal control panel to silence the alarm.

For Ice & Water models: the icon will flash on the external display. Press the button on the

external display to silence the alarm.

Remember to remove your beverage from the freezer.

To deactivate BOTTLE CHILL before 15 minutes has elapsed, press the button again. When

the function is deactivated the BOTTLE CHILL light is off on the internal control panel and the

icon is not visible on the external display (Ice & Water models only).

Fast Freeze (Elegance, Designer and Ice & Water models only)

We have created the FAST FREEZE feature to help you get the best possible results when

freezing fresh food. FAST FREEZE boosts the freezing speed by dropping the freezer to its coldest

temperature for 12 hours, which helps to ensure vital freshness, texture and taste are retained

during the freezing process.

To activate, press the button on the internal control panel. The FAST FREEZE light will be

illuminated when the function isactivated.

To deactivate before the 12 hours has elapsed, press the button again. When FAST FREEZE is

deactivated the light is off.

For best results we recommend that you activate the function before it is required. Alternatively,

activate it when placing food into the freezer.

All about the external display (Ice & Water models only)

This screen enables you to lock the water dispenser, indicates to you when BOTTLE CHILL is

activated and when your water filter requires changing.

Keys

1. Dispenser lock button and light

Locks/unlocks the water dispenser. Light is on when the water dispenser is

locked.

2. Bottle Chill indicator

Indicates when BOTTLE CHILL is on and flashes when beverage is ready.

3. Filter change indicator

Indicates when the water filter requires changing.

Note: icons will be visible only when the functions are active.

3 2 1

Fig.19 Electronic external display

Using your water dispenser (Ice & Water models only)

Dispensing

Your water dispenser has been designed for one-handed operation.

To dispense water push the dispensing pad gently, using a glass or

container. This pad requires only a gentle press to activate.

To stop the flow of water, simply pull your glass away from the

dispensing pad.

Please remember that pressing very hard against the dispensing pad

will not encourage the dispenser to operate faster or produce greater

quantities of water.

First use

Please make sure you have read and followed page 17 before using your water dispenser.

Important!

To avoid damage to property or personal injury do not put hands, fingers or objects up the

dispenser opening.

Please note that once installation is complete a few drips may appear out of the dispenser over

the next few days as the remaining trapped air is cleared.

Dispenser Lock

The DISPENSER LOCK prevents water from being dispensed. This is useful when you are cleaning

the external display or when there are small children around.

Press and hold the button for 4 seconds to activate DISPENSER LOCK.

The light above the DISPENSER LOCK icon will be illuminated.

Pressing the water dispenser pad will cause a raspberry sound indicating

to the user that water cannot be dispensed.

To de-activate the DISPENSER LOCK, press and hold the button for

4 seconds. The light above the DISPENSER LOCK icon will no longer be

illuminated and water dispensing will be enabled.

Fig.20 Water dispenser

Fig.21 Dispenser Lock

Water filter (Ice & Water models only)

All the water to your refrigerator is filtered to remove impurities through a filter cartridge located

in a position of your choice outside the refrigerator. This will need changing approximately every

6months.

There is a replacement indicator icon on the internal control panel and external display which

will appear when the filter needs replacing. It will flash, as a reminder, when water is dispensed.

Replacement filter cartridges are available through Customer Care or online at www.fisherpaykel.com

(this service is available to selected markets only). The details of the replacement filter cartridge are

on the label of the cartridge. Alternatively filter cartridges can be purchased from your Fisher &

Paykel Authorised Repairer.

Changing the water filter cartridge

It is not necessary to turn off the water supply before attempting to change the water

filtercartridge.

Grasp and firmly twist the cartridge in an anticlockwise direction (to the left when installed in the

recommended orientation) as shown in Diagram 1.

Pull the cartridge away from the filter head (down when installed in the recommended orientation)

as shown in Diagram 1 of Fig 22 below.

– It is not unusual for a few drops of water to be present when the filter is removed.

Discard the old filter.

Filter installation:

– Remove protective cap on spigot on head.

– Push the cartridge up towards filter head while rotating it in a clockwise direction (to the right

when installed in the recommended orientation) as shown in Diagram 3.

Reset filter indicator icon on the display (this will remind you when the filter is due to be replaced

again). Refer to page 30.

To flush the water filter of any trapped air, harmless carbon fines and to also check for leaks,

disconnect the tubing from the back of the refrigerator, aim the end of the tubing into a bucket,

turn isolating tap on and run at least 10 litres (10 qt) of water through. Once complete turn isolating

tap off. Reconnect the tubing.

A few drips may appear out of the dispenser over the next few days as the remaining trapped air is

cleared.

Diagram 2Diagram 1 Diagram 3

Fig.22 Changing the water filter cartridge

Water filter (Ice & Water models only)

To reset the filter indicator

Important!

We recommend the water filter to be used from the time of installation.

Do not reset indicator before filter is changed or filter monitoring will be inaccurate.

Press and hold and for 4 seconds to reset the internal and external filter indicators.

The icon on the internal and external displays will turn off when reset.

To disable the filter indicator

Note: if disabled, you will not be reminded to next change your filter.

When no filter is fitted, you can disable the filter indicator.

Press and hold and for 4 seconds to turn this feature off.

We recommend that you do not disable the filter indicator if you have a filter fitted to the

connection.

Important!

To avoid serious illness or death, do not use the water filter where water is unsafe or of unknown

quality.

The water filter cartridge needs to be changed when the filter indicator icon flashes on the

interface panel.

We recommend the water filter cartridge is replaced when the internal and external icons

illuminate. This will happen every 6 months.

If the water filtration system has been allowed to freeze, replace filter cartridge.

The rate of water flow through the water dispenser can slow down as the filter cartridge

accumulates any sediment which may be present in the water supplied to your home. This varies

depending upon your local water quality, which may require your filter cartridge to be changed

more frequently.

In cases of excessively reduced filter life we recommend that you consult a local plumber or your

water supplier for advice on suitable filtration requirements for the water supplied to your home.

Filter replacement is the consumer’s responsibility and will not be covered by the warranty except

in the case of faulty parts or materials within the filter cartridge.

If the water has not been dispensed for some time or water has an unpleasant taste or odour,

flush system by dispensing 3 litres (3 qt) of water.

If unpleasant taste or odour persists, you may wish to fit a new filter cartridge.

Using your ice maker (Ice & Water models only)

Ice On/Off

Your ice maker is designed to automatically dispense ice until it

senses that the bin is full. So the more ice you use, the more it

makes. It is even clever enough to sense when there is no bin in

place to catch the ice and it will not dispense any ice.

First use

When you first turn your refrigerator on after installation, the

icemaker will be off. The light above the ICE ON/OFF icon will be off.

To turn your ice maker on press the button. The light above

the ICE ON/OFF icon will be illuminated when the ice maker is on.

Press and hold , and together for 4 seconds then

close the door(s). The ice tray will flip. Force another cycle. The ice

tray will flip and spill the water into the ice bin. Empty water and

replace bin.

Note: the ice tray will flip only once doors are closed.

If the bin is full of ice, inserted incorrectly or if all bins are

removed, the ice maker will not operate. When the bin is inserted

correctly the scoop will be on the right hand side of the bin for

models E402B, E442B, E522B, RF522W and RF522A and at the front

of the bin for models RF610A and RF540A (refer to Fig.24).

Once your ice maker is in operation, discard the first 3 harvests

of ice (8 ice cubes are produced per harvest). This will flush away

any impurities in the water line and ensure that you get the best

quality ice. We recommend that you also do this after vacations or

extended periods of not using ice.

We recommend that you turn the ice maker off if:

– The water supply is to be off for several hours, or

– The ice storage bin is to be removed for a period of time, or

– You are going on holiday/vacation.

Fig.24 Ice storage bin and

scoop in correct position

E402B, E442B, E522B

RF522A and RF522W

RF610A/RF540A

Fig.23 Turning ice maker on

Using your ice maker (Ice & Water models only)

Information about your ice maker

Your automatic ice maker will produce approximately eight cubes of ice every 3 – 4 hours,

depending on the freezer compartment temperature and the number of door openings.

When the ICE BOOST function is activated, ice production will increase up to 30% from standard

ice making.

The ice cube tray will fill with water.

When cubes are frozen, they will be ejected from the ice tray into the ice storage bin.

Ice making will continue until the storage bin is full.

Ice making will resume once you start to use the stored ice.

Your Ice & Water product comes with a smaller ice bin inside the larger freezer bin. Attached to

the ice storage bin is the hygienic scoop for the ice. This scoop provides hygienic access to the ice.

If a large amount of ice is required, remove an ice storage bin and allow ice to fall into the larger bin.

For maximum ice storage, level the stored cubes with the ice scoop.

If ice is not used often, old cubes will become cloudy, taste stale, will shrink and may stick

together. Empty the ice storage bin periodically and wash in lukewarm water. Dry thoroughly

and place back into the correct position.

Ice boost function

This function is designed to be used for times when you require more ice eg when you are

having a party. The ICE BOOST function will increase ice production up to 30% from standard ice

making and deactivate automatically after 24 hours.

When you first turn your ice maker on, the ICE BOOST function will be off.

To turn this function on, press the button. The light above the button will be illuminated

when the ICE BOOST function is on.

The ICE BOOST function is paused once your ice bin is full.

To manually deactivate this feature press the button again. The light above the button

will be off when the ICE BOOST function is off.

Activating the ICE BOOST function will automatically turn ice making on.

Deactivating ice making will automatically deactivate the ICE BOOST function.

Important!

Avoid contact with the moving parts of the ice maker ejector mechanism, and do not place your

fingers on the automatic ice making mechanism while the refrigerator is in operation.

Do not use ice cubes that may have become discoloured, usually with a green-blue colour. If such

discolouration is noted, discard the ice cubes and contact your Fisher&Paykel Authorised Repairer.

Ensure the ice maker is connected to the filter and to a drinkable water supply only.

Installation of the water connection to the ice maker must be completed by a qualified service

technician or a qualified plumber (see installation instructions).

For manual ice making please refer to page 35.

Produktspecifikationer

Varumärke:	Fisher And Paykel
Kategori:	kylskåp
Modell:	E522BRXFDUQ4
Färg på produkten:	Zwart
Vikt:	3800 g
Bredd:	145 mm
Djup:	233 mm
Höjd:	234 mm
Blåtand:	Ja
Anslutningsteknik:	Bedraad en draadloos
Typ av strömkälla:	AC
Genomsnittlig effekt:	60 W
Rekommenderad användning:	Universeel
3,5 mm-kontakt:	Ja
USB-anslutning:	Ja
Ljudutgångskanaler:	2.0 kanalen
Högtalarplacering:	Tafelblad/Boekenplank
Bashögtalare:	Ja
Typ av högtalare:	2-weg
Diameter woofer:	120 mm
Diameter högtonenhögtalare:	25 mm
Tweeter:	Ja
Stöd för Multi-Room Streaming (MRS).:	Nee